Processes that create a synthetic gas (syn gas) in a gasification process for waste reduction, electricity generation, or steam production (CHP – combined heat and power processes) – commonly benefit from custom heat recovery systems.
Dürr MEGTEC’s industry-leading experience in air handling, drying, heating, cooling, process and combustion control can help improve the operating efficiency of your facility and maximize the performance of your equipment. By analyzing current process energy usage, we can offer solutions to reduce your energy consumption.
Rising fuel and electric costs, along with global warming concerns have changed the way industrial facilities view energy consumption. Process equipment and air pollution control systems that were installed several years ago may not reflect the energy conscious designs available today, analyzing these systems to determine energy reduction opportunities can be a very valuable practice. Recovering waste heat is one of the easiest and most utilized means of reducing energy demands at industrial facilities.
You are a farmer and would like to make money from generating electricity and heat? Then you have come to the right place. Within just a few years Dreyer & Bosse Kraftwerke GmbH have advanced to become one of the leading manufacturers of combined heat and power stations on biogas basis - we have available a complete product portfolio for energy applications of biogases or biomethane.
You are a farmer/entrepreneur and would like to make money from generating electricity and heat? Then you have come to the right place. Within just a few years Dreyer & Bosse Kraftwerke GmbH have advanced to become one of the leading manufacturers of combined heat and power stations on biogas basis - we have available a complete product portfolio for energy applications of biogases or biomethane.
For wind resource assessment campaigns in regions with long and cold winters, special measurement systems have to be designed. The challenges of cold climate regions should never be underestimated. Particularly icing is a problem. The met mast construction and the installed sensors have to be chosen carefully. The instruments have to be properly heated by a reliable power system.
With our long-term experience in wind measurement and our local installation partners we can offer complete measurement systems robust...
Cocoa processing plants are often located in remote areas with little or no access to fossil fuels. The cocoa shells represent up to 10 % of the processing capacity of a typical plant, and often have no market value. VYNCKE offers combustion systems to convert the cocoa shells into a reliable supply of steam for the sterilization, roasting and grinding process. Our systems effectively address the challenges of cocoa shells as a boiler fuel, and even allow co-generation (combined heat and power supply).
With large assembly halls to heat and very strict temperature- and humidity reqirements for their painting lines, car assembly facilities are big consumers of power and thermal energy. VYNCKE designs and builds reliable biomass energy solutions capable of not only delivering enough heat to keep assembly halls and offices warm but also guarrantee the required steadiness and accuracy in heat flow needed for the critical painting process. Hot water or superheated water is used to regulate the humidity and temperature...
Syngas (short for synthetic gas) can be burnt and used as a fuel source, the main constituents of syngas are Carbon Monoxide (CO) and Hydrogen (H), which amount for around 85% of Syngas, and it is produced by a process called Gasification.
Gasification starts with a base material which can originate from a wide variety of materials for example wood chips and pellets, plastics, municipal solid waste, sewage, waste crops, and fossil fuels such as coal. During Gasification the base material is reacted at high...
Numerous technologies and products were evaluated for this application. A monitor with no moving parts, no significant effect from turbidity, and the ability to detect the lube oil at less than 1 ppm was determined to be the best solution. Fast, reliable, and accurate detection of lubricating oil in the water was needed.
Optical instruments called fluorometers can very easily detect and measure dissolved petroleum hydrocarbons in water, and at very low concentrations. As shown in the study below, TD-4100 series monitors are able to measure xylene continuously over four consecutive weeks with a direct correlation coefficient of 0.9967 compared to GC grab sample analysis.
The PetroAlert® Series 9100 combines the selectivity of gas chromatography with the sensitivity, broad dynamic range, and hydrocarbon selectivity of a flame ionization detector (FID) providing a 30 second analysis of C1-C5 hydrocarbons required in Mud Logging for
Oil & Gas exploration, while maintaining C1-C2 separation at 200:1 concentration ratios.
We help hospitals save money by reducing their fuel bills while also lowering their greenhouse gas emissions. Our proven solutions can increase the efficiency of your heating and steam system to as much as 95% with typical project paybacks (for our combined technologies) within three to five years.
WesTech engineers water and wastewater process solutions for the power industry including water pretreatment, cooling tower makeup water treatment, and ultrafiltration pretreatment to reverse osmosis, guaranteeing SDIs less than 3. ISO 9001:2008 certified and turnkey experienced, WesTech stands ready to meet deadlines and assure minimal downtime with focused service.
Turboden ORC can produce electricity by recovering heat from industrial processes, reciprocating engines and gas turbines. The power of Turboden units generally ranges between 200 kW and 15 MW electric.
Procal supply analysers to monitor many different applications from small combustion plants to large power stations. Examples include University Boiler Plants, Carbon Black Plants, Thermal Oxidisers and Community Heating Projects.
Geothermal power plants use heat from production wells to drive turbines to make power. CSP augments the heat from the wells to boost power production. Hyperlight uses the lowest cost materials, manufacturing method, and installation technique of any CSP technology yet deployed for this purpose.