The battery charging is done through the solar panel connected to reduce the energy used from grid power and to save the electricity bills. It increases battery life because of ripple free charging from solar panel.Complete logging and monitoring of Solar (optional)
The system monitors the solar energy generated from the panels and stores the cumulative KWH generated. Monitoring through communication
In order to assure well-founded decisions in designing profitable solar power plants, the solar irradiance should be measured in the assessment phase. Irradiation is a crucial parameter for site selection and plant design and economics of plant. There are many different ways and technologies to measure the irradiance phenomena that influences the power generation of a future solar power plant. Ammonit’s solutions are designed to meet the latest standards with regard to accuracy and affordability of the measurement.
In the earlier days, the chemistry involved in solar cell manufacturing was relatively simple, using commodity chemicals. With cell efficiencies continuously on the rise and new cell concepts slowly being introduced with increased speed of processing, precise chemical concentration control is becoming crucial to obtain consistency and more cost-effective manufacturing of solar panels. This is possible by monitoring on-line the etching bath composition, a small but genuine step forward in your competitive advantage....
Regardless of whether a power plant runs on coal or natural gas, it has a very large environmental impact. Producing and transporting fuel also requires consuming resources and generating emissions. Stricter environmental requirements and increased energy costs are challenges for the industry. Solar energy can be used to preheat the water, the make-up water and the actual steam process. Solar collectors that concentrate the sunlight provide a lot of advantages for the purchaser. Read more about our products and...
Weather data is critical to optimizing the efficiency of solar power generation. Beginning with site assessment, on-site meteorological monitoring factors into overall project performance and ROI. Weather stations provide reliable information on parameter
Thermal power generation involves the combustion of a fuel to raise steam and drive a turbine to produce electricity. AMETEK Land provides the high-performance temperature measurements, emissions monitoring and safety systems demanded by this industry. High-accuracy measurements of temperature and flue gas composition are essential in optimising the combustion process, regardless of fuel used. Our instruments also help control pollution, and provide essential safety monitoring. With more than 60 years’...
Frequency inverter reconstruction of Power Plant promoted heightening of economy benefit. Frequency inverter won acceptance of user as its high reliability, flexible adjustment and simple operation. A Power Plant was set up in June, 2000. Its predecessor was one of key plants of state. The plant put into service in 1957. Now it has 4×50MW, 2×142MW, total ten boilers and six generators. Total capacity is 484MW. The plant supplies power to big enterprise near to it.
When it comes to energy production and protecting the environment, going down new paths is more critical than ever before. We do just that. SCHOTT Solar has more than 50 years of experience in solar technology and combines expert knowledge in receiver technology for solar power plants with parabolic trough technology and photovoltaics under one roof. Welcome to the future.
PV performance measurements under real outdoor conditions are done in may different ways. However, the concept of all performance investigations is to relate the input energy, which is the solar radiative flux, to the output energy, which is the electrical power produced by the PV module. EKO’s Solar Monitoring Stations, referred to as SMS, is the dedicated facility for this type of evaluation.
Procal supply analysers to monitor many different applications from small combustion plants to large power stations. Examples include University Boiler Plants, Carbon Black Plants, Thermal Oxidisers and Community Heating Projects.
The continuing establishment of nuclear power stations around the world pose unique environmental challenges for their operators. Ecotech provides air samplers to nuclear power plants for sampling of radionuclides.
A nuclear power plant`s radionuclide monitoring network enables continuous sampling of airborne particles onto sample filters contained within High Volume Air Samplers. These filters are then analysed in a laboratory in order to screen for any radiation releases. The challenge has always been to...
Biomass Power Plants generates power from biomass fuels such as wood pellets, bagasse and hog fuel. This fuels are susceptible to spontaneous combustion since it can occur at any stage of storage, production or transport. Early detection of fire or combustion is important for safety control.
As is the case in many countries, utility-scale power plants that produce renewable energy at the megawatt level are eligible to receive the Turkish government’s support via financial incentives. These power plants, whose operating costs are much lower than those of conventional power plants, can sell renewable power to electricity distribution companies at a government-guaranteed price over a fixed period of time. Companies or individuals can invest in and develop both licensed and unlicensed renewable energy...
Turboden units allow to convert the heat collected by solar collectors into electricity through an efficient thermodynamic cycle. Concentrating Solar Power systems with Turboden ORC can be cost-effective from 200 kW electric, depending on the irradiation of the installation site.
Is it suitable for you?
Concentrating solar collector field from 2 ha
Hybrid CSP plants, e.g. solar+biomass
Monitoring the stability of a sun simulator enables the researcher to improve the stability of the PV cell and precision of the I-V measurement. The sun simulator is for example used to test the produced PV solar panel and classify it according to the STC standardization.
The manufacturing process of the cells that make up the photovoltaic systems and the printed circuits require water in quantity and high quality. This water has to be managed wisely so as not to affect the productivity and the expenses of the plant.