39 products found
AEREON, part of Cimarron group Products
-
Custom Flares and VCUs for Onshore & Offshore
From basic utility flares to more complicated steam-assist, multi-point ground, or demountable derrick flares, AEREON offers a wide range of products expertly engineered to address a wide variety of gas-stream and design conditions.
-
AEREON - Utility Flares
Utility flares are one of the most common and basic flare systems. Utility flares are employed in applications which do not require smokeless burning or in applications where smokeless flaring can be achieved without the use of an additional assist medium. Utility flares therefore, do not require auxiliary gas streams such as steam or air; two fluids normally used to improve smokeless capacity. These flares are typically accompanied by a Flare ...
-
AEREON - Air-Assist Flares
Air assisted flares are comprised of two risers (waste gas and air) and a blower system that provides supplemental combustion air. Air is fed by the blower into the air riser, to combine with the process gas, which passes through its own secondary riser. Upon mixing, the high-pressure air flow causes turbulence in the waste gas stream, improving mixing, and ultimately combustion efficiency. These flares generally dispose of heavier waste gases which ...
-
AEREON - Gas-Assist Flares
Gas-assisted flares are comprised of two risers (waste gas and assist gas) and an assist gas distribution ring at the tip that provides turbulence with combustion air and waste gas at the flare tip. Upon mixing, the increased turbulence in the waste gas stream, improves combustion efficiency and smokeless performance. These flares generally dispose of heavier waste gases which have a greater tendency to smoke and are favored in applications where ...
-
AEREON - Steam Assist Flares
Steam assisted flares are flares designed to dispose of heavier hydrocarbon gases which have a tendency to smoke. In order to prevent smoke formation, steam is injected into the waste stream using peripheral steam rings, center stream spargers and/or inner induction tubes. Steam flares are used in applications where high pressure steam is available on site. Steam flares are typically found in downstream applications where high efficiency combustion of ...
-
AEREON - Model Mach-1 - Fixed Orifice Sonic Flares
Mach-1 sonic flares are used in both onshore and offshore applications to dispose of high pressure waste gas streams with high smokeless capacities. By efficiently inducing high volumes of ambient air for more complete, smokeless combustion at sonic velocities, this advanced flaring technology allows for reduced levels of radiation and can be placed at lower, less visible elevations, allowing for a more cost-effective flaring solution. Mach-1 sonic ...
-
AEREON VariMach - Variable Orifice Sonic Flare
The VariMach sonic flare tip features spring-actuated variable sonic nozzles to allow the exit area to vary with pressure, ensuring constant sonic velocity of the exiting waste gas. This industry proven technology guarantees sufficient inspiration of air to ensure 100% smokeless combustion and infinite turndown. Radiation levels are also minimized throughout the entire range of flow, yielding shorter stack heights and reducing material costs. ...
-
AEREON - Model MPGF - Multi-Point Ground Flare Systems
When ample real estate is available, multi-point ground flare (MPGF) systems are an economical approach to enclosed (hidden) and smokeless combustion of large amounts of process gas. By inducing gas through a large array of high-pressure burning points/burners, smokeless combustion can be achieved with high turndown, while concealing all radiation within the walls reducing exposure to personnel. MPGF systems provide smokeless capacity and no ...
-
AEREON - Model VCUs - Vapor Combustion Unit
As an alternative to recovery, hydrocarbon vapors may be destroyed in a flare, combustor or a thermal oxidizer. For many applications, a device known as a combustor can be successfully used as a safe and economical method of controlling vapors from the handling, storage or loading of volatile liquid hydrocarbons or ethanol when recovery of the vapors is not a viable ...
-
AEREON - Model Triton - Water Injected Sonic Flares
Triton sonic flare technology allows for safe, efficient and smokeless flaring at elevated oil and gas production rates by injecting sea water into the flame envelope. High pressure sea water injection reduces flare emissions, helps minimize overall radiation levels from the flame, abates combustion noise, and preserves flame characteristics during high wind events. The Triton sonic flare is best-suited for offshore applications involving high pressure ...
-
AEREON - Flame Ring Flares
Carbon dioxide is often used in fire extinguishers and snuffing systems with the intention of effectively extinguishing flames. When CO2 gas is a large percentage of a waste gas stream, at times it proves difficult to maintain a lit flare without the use of assist gas or a properly designed flame ring. Flare Industries’ industry-proven Flame Ring Flare Technology is recommended in low-BTU applications such as those involving large quantities of ...
-
AEREON - Chimera Liquid Burner
The Chimera was developed to flare liquid hydrocarbons without liquid fallout or soot formation (smoke). These burners provide excellent service for various onshore applications that require high destruction efficiency of liquid hydrocarbons. When oil is flared, a high pressure media such as an air, gas, or steam is required to mechanically atomize the heavy hydrocarbons for proper and stable ...
-
AEREON - Peacock Liquid Burner
The Peacock Burner was developed to flare liquid hydrocarbons without liquid fallout or soot formation (smoke). These burners provide excellent service for well testing operations and have been used in applications in the Gulf of Mexico and Arabian Gulf. When only oil is flared, a high pressure air or gas source is required to provide mechanical atomization which ensures the mixture is a fine mist as it exits the burner nozzle. This particular burner ...
-
AEREON - Pit Flares
Pit Flares are generally selected and designed in order to combust a mixture of vapor and liquid from a single source. While most often designed to operate non-smokelessly, through use of Flare Industries’ various Pit Flare technologies, smokeless operation can often be achieved. The flare pit (or “Burn Pit”) is usually constructed of an excavation, lined with a non-combustible lining of rock or refractory material. Often coupled with ...
-
Standard Flares for O&G Production
With the rapid growth of oil and gas production in the North American shale plays and other areas, AEREON has answered the call with a series of 40CFR60.18 and QuadOa compliant standard flares and combustors that deliver the high performance and rapid delivery you need at very economical price points.
-
AEREON - Model Utility Series - Flare Systems
Utility flares are one of the most common and basic flare systems. Utility flares are employed in applications which do not require smokeless burning or in applications where smokeless flaring can be achieved without the use of an additional assist medium (I.e. For burning of lighter gases). Utility flares therefore, do not require auxiliary gas streams or assist air; two mediums normally used to improve smokeless capacity. These flares are typically ...
-
AEREON - Model Cyclone Series - Air-Assist Flares
AEREON's Cyclone Series Air-assisted flares are comprised of two risers (waste gas and air) and a blower system that provides supplemental combustion air. Air is fed by the blower into the air riser, to eventually combine with the process gas, which passes through its own secondary riser and is distributed at the flare tip through a proprietary AEREON Starfire burner tip. Upon mixing at the flare tip, the high-pressure air flow causes turbulence in the ...
-
AEREON - Model Inferno Series - Gas-Assist Flares
AEREON's Inferno Series Gas-assisted flares are flares that use an additional source of high pressure gas at the flare tip to mix with the waste gas and create additional turbulence to ensure adequate mixing with air, which in turn provides for smokeless combustion. The waste gas is further distributed at the flare tip through AEREON's proprietary Starfire burner, optimizing gas and air mixing. Gas-assist flares are typically utilized when you have a ...
-
AEREON - Model Momentum Series - Non-Assisted Flares System
AEREON's Momentum Series of non-assist flares provide smokeless performance without the need of additional air-blowers or assist gas for both high pressure and low pressure gas streams. Leveraging the increased momentum of gas that is passed through a simple nozzle or restricted opening, the waste gas intimately mixes with the ambient air and provides for smokeless operation while meeting all Quad O and 40 CFR 60.18 ...
-
AEREON - Model Ghost Series - Enclosed Combustors
With the roll out of Quad O regulations in the USA, crude/condensate tank batteries and well pads are required to conform to reduced emission levels if they have the potential to emit over 6 tons of VOC per annum. One of the three emission control end-of-line devices can be used: Flares, Enclosed Combustors or VRUs. When enclosed flames and smokeless combustion are required for low pressure tank vapors, or other VOC destruction applications, AEREON's ...
-
Ignition Systems & Pilots
When you’re shopping for ignition systems or pilots, high reliability and safety are paramount. AEREON offers both, backed by proven records and unparalleled ease of use.
-
AEREON - Model 100 - Continuum Ignitor
The Model 100 Continuum Ignitor utilizes a high voltage electric arc to ignite a combustible air/gas mixture. This arc typically occurs every 20 seconds for a two second duration (timing is adjustable). The Continuum provides a spark inside a ‘slipstream’ chamber that diverts a portion of the waste gas to create a combustible air/gas mixture. This allows the Continuum ignitor to function without additional pilot gas which is very valuable ...
-
Electronic Pilot Systems
When looking at ignition systems and pilots, you need a product with high reliability and a safety record to match. AEREON offers innovative, effective ignition systems and pilots with an ease of use and a proven record.
-
AEREON Energex - Model 250 - Ignition High Alloy Stainless Steel Pilot
The Model 250 Energex Pilot is a high alloy, stainless steel pilot which combines a high voltage electronic excitor and a high energy spark rod to provide rapid, reliable ignition. More importantly, the Energex pilot provides instantaneous re-ignition if the pilot should ever lose its flame. This pilot system uses a fuel gas line much like other standard pilots, however instead of a flame front generator it utilizes an excitor capable of producing a ...
-
AEREON Geminex - Model 255 - Pilot System
The Model 255 pilot is a combination of our Model 245 pilot and Model 250 Energex pilot. The Model 255 pilot can be ignited using a flame front generator and/or the high-energy excitor (electronic sparking device). This pilot inherently provides redundancy in the event that one ignition system should fail to ignite the pilot for any reason. This pilot is a common selection in critical applications that require redundant ignition ...
-
AEREON Retrax - Model 270 - Electronic Pilot System
The Model 270 RETRAX is a high-tech, retractable, electronic pilot which meets the technical requirements of our clients. This advanced design allows the plant operators to lower the RETRAX pilots individually or all at once for ease of maintenance. Since the RETRAX can be lowered from grade, operators need not wait for a plant shut down to service the pilots. The Model 270 RETRAX allows customers to forego ladders and platforms altogether which ...
-
AEREON - Model 275 - Retractable Pilot
The Model 275 pilot is a high-tech, retractable pilot that has been adapted to operate on both high-energy electronic ignition and flame front ignition. Technically, the Model 275 pilot is a combination of the Model 270 Retrax Pilot and the Model 255 Geminex FFG Pilot, allowing for redundant ignition technology and retractability. This design allows the operator to retract pilots individually or all at once for ease of maintenance. Since the Model 275 ...
-
AEREON - Model 850 - Flamex Pilot Ignition System
The Model 850 Pilot is a time-proven product that combines electric spark ignition with continuous spark monitoring, thermocouple monitoring, and retractability. The combination of these highly-demanded features has made the high-alloy, stainless steel Model 850 Pilot one of the most well-received ignition systems on the market. This electric pilot provides a rapid, direct spark every 10 to 20 seconds, ensuring reliable ignition. The Model 850 features ...
-
AEREON DuraSpark - Model 1000 - Heavy Duty Pilot
The new Model Duraspark 1000 Heavy Duty Pilot was developed specifically for the rigors of the oil-patch, providing additional layers of protection and heat shielding of critical components. The transformer box has also been placed at grade (vs. near the flare tip) reducing heat stress of these critical components. Available with retractable packages, the DuraSpark 1000 will improve system reliability and life ...
-
Flame Front Generator Pilot Systems
Flame front generators (FFGs) are effective ignition systems that have used for decades in flaring applications. The reliability, rugged construction, ease of operation, and economic advantages have made the FFG one of the most popular pilot ignition systems in the industry.
-
AEREON - Flame Front Generators
Flame front generators are effective, time proven ignition systems which have been widely used in flaring applications for decades. The inherent reliability, rugged construction, ease of operation, and its economic advantages have allowed the flame front generator (FFG) to remain one of the most popular forms of pilot ignition in the industry. The FFG is easily adaptable to any pilot system which incorporates an ignition tube and may be installed up to ...
-
AEREON - Model 245 - Flame Front Generator Pilot
The Model 245 Fuel Efficient Flare Pilot is a high alloy, stainless steel pilot composed of fuel gas line, ignition line, inspirator and optional thermocouple. The pilot head assembly includes a 310 stainless steel flame retention nozzle and wind shroud for extended service life capable of sustaining a stable flame in winds of up to 150 mph. Fuel gas passes through an inspirator at the base of the pilot, inducing air into the line and providing a ...
-
Combustion Equipment Accessories
AEREON’s line of combustion equipment accessories provide you with cost savings, reliability, durability and rapid response time.
-
AEREON - Dynamic (Velocity) Purge Seal
The dynamic (velocity) seal is a simple innovation which ensures significant cost savings over time. The reverse conical baffle design reduces flow area in the flare tip while simultaneously increasing purge gas velocity. In combination with the dynamic seal, a constant flow of purge gas will maintain a seal in flare system, ensuring that air infiltration does not occur. A vortex effect is created as the exiting purge gas inspirates intruding air. This ...
-
AEREON - Sentinel Ultraviolet Flame Monitor
The Sentinel flame monitor reliably provides remote flame detection up to 550 feet away, durability, ease of maintenance and rapid response time. If the monitor detects the absence of a flame for an adjustable amount of time, a set of dry form C contacts are activated and the pilot re-ignition system is set into motion. Response times are markedly quicker than those of a standard thermocouple since the monitor can immediately sense the loss of flame. ...
-
Elevated Flares and Enclosed Ground Flares for the Biogas Industry
-
AEREON - Model Momentum Series - Biogas Flares and Enclosed Flares
The Momentum Biogas series of elevated flares is our most economical line of combustion equipment for the biogas sector, offering a cost-effective solution with rapid delivery. Momentum flares utilize a specially designed “burner and shroud” system to manage the intricate mixing with ambient air to provide a high DRE (98%) and high turndown ratio in a simple, yet effective, product. The Momentum Series is a reliable method of emission ...
-
AEREON - Model Ghost Series - Enclosed Flares
The Ghost series of enclosed biogas flares is a simple and cost effective combustion solution for a variety of applications where a hidden flame is required. The superior design, high quality stainless steel construction and unmatched versatility make the Ghost Series Enclosed Flares an exceptional choice for emissions control within the biogas and wastewater industries. Additionally, each product within our Ghost line is able to perform under the ...
-
Thermal Oxidation/Incineration Systems
AEREON offers a complete line of thermal oxidation/incineration systems, including direct-fired, recuperative, regenerative, catalytic, tail gas and halogenated models. We use only the highest quality components and materials to help eliminate unnecessary downtime and maximize the life of the product.
-
AEREON - Tail Gas Incineration Units
Hydrogen sulfide or H2S is a lethal gas generated in refineries, petrochemical plants, and gas handling facilities. Sulfur recovery units produce tail gases that contain relatively substantial amounts of H2S. AEREON designs a special type of incinerator, designed to eliminate the H2S components, while inhibiting the creation of corrosive acid by-products. Systems of this nature typically include dispersion stacks in efforts to disperse trace H2S ...
-
AEREON - Halogenated Thermal Incineration Systems
AEREON's halogenated thermal oxidizer systems are designed to handle hazardous halogenated streams produced from various chemical processes in a safe and effective manner. Systems are designed to maintain high destruction efficiency of the compounds with an effective high chamber temperature and residence ...
-
Ultra-Low Emissions Systems
AEREON’s line of CEB ultra-low NOx and CO emission-burner systems are unlike any other in the market. They utilizes proprietary, premixed, surface-combustion technology to burn VOC-laden waste gases in any application, from continuous and batch operations to emergency back-ups of other equipment. Compact and easy to install and maintain, they start up quickly from idle state and are economical to operate.
-
AEREON CEB - Certified Ultra-Low Emissions Burner
The Certified Ultra-Low Emissions Burner (CEB) is an ultra-low emissions vapor device that utilizes premix surface combustion to effectively combust waste gases in a compact footprint. With VOC destruction efficiencies of up to 99.99% and a NOx emissions guarantee of ≤ 15 ppmv at 3% oxygen, carbon monoxide emissions guarantee of, smokeless operation and no luminous flame, the CEB is the best solution for your VOC destruction requirements. It is ...
-
Enclosed Vapor Combustion Systems
AEREON’s enclosed vapor combustion systems include marine/rail/truck loading vapor combustors, Quad-O-certified enclosed combustors for O&G production sites, and enclosed flares for landfill, biogas and other non-Quad-O-regulated applications. We use only best-quality components and materials in our vapor combustion systems to help reduce unnecessary downtime and maximize the life of the product.
-
AEREON - Marine/Rail/Truck Loading Vapor Combustors
AEREON is an expert in the design, manufacture and service of all types of vapor combustion units (VCU's). An AEREON VCU is commonly used for marine, rail and truck loading and can be specially designed for other waste streams. AEREON's VCUs are guaranteed to meet all safety regulations and emissions limits. Custom and standard devices are available allowing you to pick the right mix between perfect fix and cost for your ...
-
AEREON - Model Quad O/Oa - Designed and Certified Enclosed Combustors
With the roll out of Quad O regulations in the USA, crude/condensate tank batteries and well pads are required to conform to reduced emission levels if they have the potential to emit over 6 tons of VOC per annum. One of the three emission control end-of-line devices can be used: Flares, Enclosed Combustors or ...
-
AEREON - Model VCUs - Vapor Combustors
Hydrocarbon vapors may be destroyed in a flare, combustor or a thermal oxidizer. For many applications, a simple vapor combustor can be successfully used as a safe and economical method of controlling vapors from the handling, storage, or loading of volatile liquid hydrocarbons or other compounds when recovery of the vapors is not a viable ...
-
Gas and Vapor Recovery System
AEREON is one of the world’s largest manufacturers and service providers for carbon- and compression-based vapor recovery units (VRUs). Since 1980, our Jordan Technologies division has designed, manufactured and serviced VRUs across multiple industries, including liquid-loading terminals, O&G production and midstream distribution, and gasoline stations.
-
AEREON Wildcat - Wellhead Compression Units
AEREON offers our own WILDCAT natural gas compression systems for wellhead applications as rental or lease equipment. Through testing, we can identify flow improvement up front and determine the appropriate standard system for your gas compression and budgetary needs. AEREON's gas compression systems have been used successfully for many years. Systems installed on coal bed methane wells, gas wells and oil wells have generated increases in sustained ...
-
AEREON - Retail Gasoline Station Recovery Unit
Miniaturized VRUs recover gasoline vapors otherwise lost through normal storage tank evaporation, or during fuel deliveries to retail gas stations. The recovered vapors are returned to storage tanks for eventual sale to customers, effectively reducing product loss and increasing retailer ...
