load-current Downloads
78 downloads found
Type DingoNominal voltage 12/24/32/36/48 VMax. solar panel current 20 AMax. load current 20 ARegulation set points 4 preset programs or user adjustWeight 455 gAmbient temperature range –20 to +55 °CGrounding negative grounding possibleMax. wire size 16 mm2 (6 AWG)Mounting hole spacing 116 mmMounting hole size 5 mmDimensions (W x H x D) 137 x 121 ...
This single phase data logger is specifically designed to monitor one voltage channel and one current. It allows you to monitor the main voltage supply and the load current, enabling staff to determine whether a voltage problem is load related or not. ...
With a crest factor of up to 5:1, the NSG 1007 series sources can drive difficult nonlinear loads with ease. Since many modern products use switching power supplies, they have a tendency to draw high repetitive peak currents. The Teseq sources can deliver a repetitive peak current of up to three times their rated continuous ...
This control unit features a powerful processor, configurable CAN channels and a flexible I/O system to meet the needs of a variety of demanding applications.Techncial Data Dimensions Change to 146.6mm L x 134.2mm W x 58.6mm HWeight TBDStorage Temperature Range -40 - +125 °C Operating Temperature Range -40 - +105 °C(USB use is limited to 85°C) IP Rating IP67 Operating Altitude 0 - 4000 mSupply ...
This control unit features a powerful processor, configurable CAN channels and a flexible I/O system to meet the needs of a variety of demanding applications.Techncial Data Dimensions 212.6mm L x 134.2mm W x 58.6mm HWeight 43.2 ounces (1225 grams)Storage Temperature Range -40 - +125 °C Operating Temperature Range -40 - +105 °C(USB use is limited to 85°C) IP Rating IP67 Operating Altitude 0 - ...
The DC64P has been designed for direct current loads, such as motors used on small winches. The DC64P is a monoblock construction, resulting in a compact design which is compatible with modern electronic control systems. Devised for both interrupted and uninterrupted loads, the DC64P is suitable for switching Resistive, Capacitive and Inductive ...
General Since S&C Mini-Rupter Switches are capable of switching rated load currents at full voltage, no interlocking with secondary protective equipment is required. ...
Datasheet_MPS series_1/1_e_2011-04-01_Subject to change without notice• 12/24/48 V (automatic oder manually selectable)• Low-voltage or overcharge disconnect (adjustable)• Overcharge protection• Pulse-width modulation or two-point series switching• Can also be used with hybrid systems• Excess energy management• Flexible grounding• DIN rail mountingMPS series (45 – 80 A) Modular Power ...
ATI-156E-L5 Efficiency Range (%): 14.6~14.7. Load Current @0.5V (A) : 7.031~7.082. Rated Power(Wp): 3.529. Maximum PowerCurrent(A): 7.088 . Short CircuitCurrent(A): 7.601. Maximum PowerVoltage (V): 0.500. Open CircuitVoltage(V): 0.606. ...
This control unit features a powerful processor, configurable CAN channels and a flexible I/O system to meet the needs of a variety of demanding applications.Techncial Data Dimensions 212.6mm L x 134.2mm W x 58.6mm HWeight 43.2 ounces (1225 grams)Storage Temperature Range -40 - +125°C Operating Temperature Range -40 - +105°C (USB use is limited to 85°C) IP Rating IP67 Operating Altitude 0-4000 ...
Category : Standard Round Brush. Part Number : M22E-13. Frame Width [mm] : 22. Frame Height [mm] : 22. Frame Depth [mm] : 18. Operating Voltage - Lower [V] : 3. Operating Voltage - Upper [V] : 4. Rated Voltage [V] : 3.5. Rated Load [mN per m] : 9.3. Rated Speed [rpm] : 4000. Rated Current [mA] : 1800. No Load Speed [rpm] : 6100. No Load Current [mA] : 120. Starting Torque [mN per m] : 27. ...
Output Voltages : Two independent output voltages (both positive or both negative or one positive and one negative), Load currents : Both outputs are displayed on two seperate 3 1/2 meters, Protection : Short circuit and Overload protected Ripples Less than 3 mV rms, Regulation : ± 0.05% from no load to full ...
The transducer SINEAX F535 (Fig. 1) converts the frequency difference of two synchronised supplies into a load independent DC current or a load independent DC voltage proportional to the measured ...
/BOX* Overrating fusesCYLINDRICAL FUSESDIMENSIONSSIZE A B C D E8,5x31,5 8,5 31,5 6,3 – –10,3x38 10,3 38 8,5 – –14,3x51 14,3 51 11,5 8 422,2x58 22,2 58 15,5 8 4FUSESCYLINDRICALgGTECHNICALaM1 411101 411201 400 20 – – – 10/1002 411102 411202 400 20 – – – 10/1004 411104 411204 400 20 – – – 10/1006 411106 411206 400 20 – – – 10/1008 411108 – 400 20 – – – 10/10010 411110 411210 400 20 – – – ...
This control unit features a powerful processor, configurable CAN channels and a flexible I/O system to meet the needs of a variety of demanding applications.Techncial Data Dimensions 146.6mm L x 134.2mm W x 58.6mm HWeight TBDStorage Temperature Range -40 - +125°C Operating Temperature Range -40 - +105°C (USB use is limited to 85°C) IP Rating IP67 Operating Altitude 0-4000 mSupply Voltage ...
The RW150 is designed for use in telecommunications and power distribution applications where an uninterrupted current load is switched. These contactors are primarily for use with Direct Current loads but can also be used with Alternating ...
The transducer SINEAX G537 (Fig. 1) converts the phase angle difference of two synchronised supplies into a load independent DC current or a load independent DC voltage proportional to the measured ...
AMF3.1 is a full Automatic Mains Failure unit intended to be used for Gen-Set applications. The controller can be used with single or three phase mains systems. The unit is designed with high process power for versatile and accurate control of all Gen-Set functions. It controls 3 phase mains and single phase generator voltage and also monitors generator load ...
The transducer SINEAX I552 (Fig. 1) converts a sinusoidal or a distorted AC current into a load independent DC current or a load independent DC voltage proportional to the measured ...
The instrument change the measured value into a. proportional load independent DC current or DC voltage.. The transducer fulfi ls all the important requirements and regulations. concerning electromagnetic compatibility EMC and Safety (IEC. 1010 resp. ...