power-sensor Downloads
38 downloads found
Premium
The unique SPSR (Self-Powered Sensor) with internal rechargeable batteries provides the required power to any one of (4) Monarch Sensors (see below). The TTL compatible output is switch selectable as either positive going 0-5 V pulses or negative going 5-0 V pulses provided on a BNC connector. The internal rechargeable batteries provide 40 hours of operation between charges. For continuous ...
AVTECH’s Power Sensor monitors the on/off state of a power source, such as main power, a UPS, surge protector or standard wall outlet. Simply plug the Power Sensor into the source you wish to monitor. Install multiple Power Sensors to generate alerts when one source fails and the back up takes ...
Dual Output Loop Power Sensor, 4-20 Ma Output Proportional To Vibration In Velocity With °C Temperature Output, Top Exit 3 Pin Connector. -40 to 212°F (-40 to 100°C) Temperature Range. Welded, Hermetic Sealing. Continuously Monitor & Protect Important Machinery. ...
Dual Output Loop Power Sensor, 4-20 Ma Output Proportional To Vibration In Velocity With °C Temperature Output, Side Exit 3 Pin Connector. -40 to 212°F. (-40 to 100°C) Temperature Range. Welded, Hermetic Sealing. Continuously Monitor & Protect Important Machinery with 4-20 and Temperature Outputs. ...
Loop Power Sensor, 4-20 Ma Output Proportional To Vibration In Velocity, Top Exit 4 Pin M12 Connector. -40 to 212°F. (-40 to 100°C) Temperature Range. Welded, Hermetic Sealing. Continuously Monitor & Protect Important Machinery. ...
The PM Series calibrator simplifies the tedious and complex process of RF power sensor calibration. The goal is to realize consistent, cost effective and traceable calibrations. ...
AVTECH’s Mini UPS and Power Sensor (MUPS) monitors the on/off state of a power source, such as main power, a UPS, surge protector or standard wall outlet, and also provides up to 15 minutes of battery backup for your Room Alert or other 5V ...
Loop Power Sensor, 4-20 Ma Output Proportional To Vibration In Velocity, Side Exit 2 Pin Connector. -40 to 212°F (-40 to 100°C) Temperature Range. Welded, Hermetic Sealing. Continuously Monitor & Protect Important Machinery. ...
Loop Power Sensor, 4-20 Ma Output Proportional To Vibration In Velocity, Top Exit 2 Pin Connector. -40 to 212°F (-40 to 100°C) Temperature Range. Welded, Hermetic Sealing. Continuously Monitor & Protect Important Machinery. ...
AVTECH’s Digital Active Power Sensor monitors active power status and ambient room temperatures. Simply strap the sensor to the AC electrical cord of any device that draws more than 100 W. There’s no need to unplug the device, modify the cord, or require an electrician to connect within a main panel, making it easier than ever to monitor any electric device. When the connected device ...
AVTECH's Main Power Sensor provides real-time recognition of a power source going off or coming on. Common use is to monitor the power supply of a main, single-phase, UPS or backup power source. Users will often install multiple Power Sensors so they can be immediately informed when one source fails and then immediately informed that the back up power source has taken over. Because AVTECH ...
PowerZook is a unique, non-invasive, PoE power sensor that can monitor single phase (3-core) PDUs up to 32A, including many of those from the leading PDU manufacturers. PowerZook provides users with the ability to quickly start harvesting PDU power usage data using SNMP without interruption to power, modification to power cables, or ...
PowerZook is a power sensor that can be installed without system downtime to provide rack input power readings via SNMP. PowerZook clips around the outside of rack input power cables to monitor the power draw of the rack equipment for loads of up to 32A. PowerZook provides a smart alternative to smart PDU’s where system downtime and/or higher costs are not viable ...
The Pulse S0 is used to remotely read metering data from water, gas, electricity or energy meters. It turns existing meters into smart meters via the SigFox network. ...
ByWatteco
The Panoramic Power PAN-10 Wireless Sensor is appropriate for granular monitoring of individual circuits and devices with a max hot-wire outer diameter of .28 inches (7 mm), measuring currents of 0–63 A. ...
LVS-2+ is a comprehensive fusion and perception software stack supporting premium surround-view L2/L2+ ADAS highway assistance and 5-star NCAP 2025/GSR 2022 safety applications. LeddarVision™ low-level fusion (LLF) and perception technology enables implementation of entry-level to premium ADAS utilizing a single architectural approach, efficiently scaling computational power with sensor additions ...
The boiler is supplied as standard with the OX 2001 microprocessor control unit.After a power cut lasting longer than three minutes the power to the boiler is ramped up in stages (see table). ...
Universal interface converter Eurosens Destination 02 is designed for professional adjustment of Eurosens sensors, as well as other third-party equipment. It contains interfaces K-line, RS-232 and RS-485. Contains a power converter to power the connected sensor from the computer without using external ...
GDC (General Displayer & Controller) series terminal are designed for continuous measurements with Cross Smart Sensors in a general purpose industrial or municipal environment. GDC terminals have the ability to extend network by intelligent sensors with RS485 output, Modbus RTU protocol. GDC terminals supply power to sensors ...
ARTEMIS LIVE: A PASSIVE TRACKING AND SURVEY TOOL USED ON LIVE AC OR UNIPOLAR DC CABLES THAT ARE POWERED. The Artemis sensors are set to look for 50/60 Hz or a harmonic from the live power transmission (residual in AC phase imbalance, or from AC-DC conversion). Unlike alternative technologies on the market, Artemis uses a model-based technique looking at the 3D magnetic field properties to ...
BySMD UK