Cogeneration Equipment For Energy Management In USA
-
ShowcaseManufactured by Solar Turbines Incorporatedbased in USA
A gas turbine engine is a type of internal combustion engine. Essentially, the engine can be viewed as an energy conversion device that converts energy stored in the fuel to useful mechanical energy in the form of rotational power. The term “gas” refers to the ambient air that is taken into the engine and used as the working medium in the energy conversion ...
-
PremiumManufactured by HRS Heat Exchangers Ltd.based in UNITED KINGDOM
The HRS Digestate Concentration System (DCS) reduces the volume of digestate from anaerobic digestion while increasing its value. In most situations, it is able to do this using surplus heat from the CHP engine or biogas boiler, which can be used up to four times by incorporating multi-effect evaporation ...
-
PremiumManufactured by HRS Heat Exchangers Ltd.based in UNITED KINGDOM
The HRS Biogas Dehumidification System (BDS) removes water from biogas, protecting combined heat and power (CHP) engines from corrosion and cavitation. It can be supplied with a heat recovery section, increasing the overall efficiency of anaerobic digestion (AD) ...
-
PremiumManufactured by Solar Turbines Incorporatedbased in USA
If you need electricity and thermal energy simultaneously, a cogeneration system may be your solution, and can offer a favorable return on investment. Cogeneration allows you to benefit from two or three forms of energy for the price of one, with minimal environmental impact. These systems can turn clean-burning natural gas into cost-effective, reliable electricity, use steam for production ...
-
PremiumManufactured by Solar Turbines Incorporatedbased in USA
Solar's modular concept for gas turbine generator sets has been optimized for transportation and the scope has been minimized for civil works with our Power Generation Module (PGM). Good for non-hazardous applications only, our PGM solution results in shorter installation and commissioning times, and reduces overall costs for our ...
-
PremiumManufactured by HRS Heat Exchangers Ltd.based in UNITED KINGDOM
The HRS G Series is a complete stainless steel multitube heat exchanger designed specifically for exhaust gas cooling and thermal recovery applications. Similar to the HRS K Series, the exhaust gases flow through the interior tubes and the service fluid flows through the surrounding shell. Using our corrugation technology, heat transfer and efficiency are increased over standard smooth tube ...
-
PremiumManufactured by Solar Turbines Incorporatedbased in USA
Solar Digital is the global organization responsible for InSight Platform™ technology and the relentless innovation of the entire ecosystem, capabilities and customer user experience. We are obsessively customercentric with a passion for cutting edge technology. With deep expertise in machine data acquisition, cyber security, software development, OEM product knowledge, and big data ...
-
based in USA
The 9E gas turbine is GE's robust and proven 50 Hz workhorse. With more than 600 units shipped, it has accumulated over 23 million hours of utility and industrial service-often in arduous climates ranging from desert heat and tropical humidity to arctic cold. 9E gas turbine systems are also designed for reliable operation and minimal maintenance at a competitively low installed cost. The 9E gas ...
-
Manufactured by JX Crystals, Inc.based in USA
Thermophotovoltaic (TPV) cells generate power from certain bandwidths of light, similar to solar cells. JX Crystals focuses upon infrared frequencies, which are emitted from heat. Specially designed Gallium Antimonide (GaSB) cells are used to most efficiently convert the heat emitted from ignited ...
-
Manufactured by Seko Industries Srlbased in ITALY
Power (kWel): 526. Cogenerator electrical efficiency %: 40.4. Cogenerator overall efficiency %: 83.10. Electrical energy produced (kWh/year): 4313200. Thermal energy available (kWel): 556(including fume ...
-
Manufactured by Kraft Energy Systems LLCbased in USA
The simple solution for lowest emissions and steady performance. KN Series Natural Gas CHP modules harness the reliability of naturally aspirated rich-burn engines with on-board 3-way dry exhaust catalyst to meet the most stringent air permitting requirements while providing superior electrical load acceptance and transient stability in island mode/grid outage operation. Chose from 4 models or ...
-
based in USA
GT MASTER® simulates performance of a given plant at different operating conditions, such as different ambients, loads and control set-points. A GT MASTER plant model is defined by its hardware, by contrast with a GT PRO model which is defined by the assumptions used to create the hardware. The 4,000+ inputs which define plant hardware and control set-points are all initialized upon ...
-
based in USA
STEAM PRO® automates the process of designing a conventional (Rankine cycle) steam power plant, guiding the user to rapidly and easily attain an optimal configuration and its technical parameters. The user inputs design criteria, starting with the big picture and progressing in a logical sequence into greater details. Built-in expert logic automatically selects appropriate options and inputs ...
-
by Trevi nvbased in BELGIUM
Together with BiogasTec Trevi builds facilities for anaerobic digestion, also called biogas plants. A biogas plant is a plant which - as the name implies - produces biogas. This gas is a renewable energy source based on organic material. This organic material concerns manure, waste and energy crops. Biogas is certainly not new. Spontaneous fermentation of organic material with formation of gas is ...
-
Manufactured by G.C. Broach Companybased in USA
The G.C. Broach Company has designed and manufactured over 50 waste heat recovery boilers. A waste heat boiler manufactured by The G.C. Broach Company is generally manufactured in accordance with “API 560 Fired Heaters for General Refinery Service” specifications and is usually ASME Section VIII Division One code stamped. Waste Heat Recovery Boilers are also referred to as ...
-
Manufactured by Northeast Energy Systemsbased in USA
With our deep insights on project development of combined heat and power technologies, Jenbacher Type 4 installations provide substantial reduction of the environmental footprint in facilities that have consistent electrical and thermal requirements. Pushing the boundaries of efficiency in the 800 to 1500 kW power class, the Jenbacher Type 4 is characterized by its high power density and maximum ...
-
Manufactured by DMT Environmental Technology BVbased in NETHERLANDS
Standard system for removal of H₂S out of biogas. DMT has developed the DMT Sulfurex gas desulphurisation scrubber. The DMT-Sulfurex desulphurisation process has proven to be cost effective for smaller applications (see references) due to its low capital and running costs, whereas traditional gas desulphurisation systems are not designed for smaller applications and can only be cost ...
-
Manufactured by Dalkia Aegis, EDF Groupbased in USA
A powerful enhancement of the PowerSync line, both the PowerVerter PV-75 and PV-100 reflect continual innovation to meet consumer needs. These unique, standalone products represent a redefinition of the CHP experience, marrying the trademark savings and emissions reductions with black start capability. The PowerVerter systems offer the most dynamic cogeneration experience on the market, reducing ...
-
Manufactured by Clarke Energybased in UNITED KINGDOM
Continuously refined on GE Jenbacher’s extensive experience, the GE Jenbacher type 6 engines are reliable, advanced products serving the 1.8 to 4.4 MW power range. It’s 1,500 rpm engine speed results in a high power density and low installation costs. The type 6 pre-combustion chamber achieves maximum efficiency with low emissions. Proven design and optimised components enable a ...
-
Manufactured by Forney Corporationbased in USA
adVantage Duct Burners perform in the most challenging conditions. Premium components and patented technology join to perform like no other duct ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you