Combustion Plant (Combustion) Equipment
-
based in ITALY
Operating Principals: The plant basically consists of three vertical chambers filled of high thermal capacity ceramic material (a preheating inlet gas chamber, a heat recovery of purified gas from combustion chamber and a cleaning chamber with fresh air) and a combustion chamber with modulating burner that connect up the 3 chambers. The ...
-
based in ITALY
Operating Principals: The unit is mainly made up with a shell and tube heat exchanger and a combustion chamber equipped with a modulating burner. The gas containing V.O.C. is preheated passing through the shell and tube heat exchanger up to a temperature close to 450 ÷ 550 °C by mean of the heat released by combustion gases which ...
-
Manufactured by Polytechnik Luft- und Feuerungstechnik GmbHbased in AUSTRIA
Air and water-cooled horizontal and step grates. Grateless firings and combinations. Stationary fluidised ...
-
Manufactured by Cematekbased in ITALY
The regenerative combustion plant is based on the concept of achieving a high thermal energy recovery with the aid of large ceramic masses that – during the heat recovery phase – absorb the heat from combustion gases and – during the regeneration phase – release the accumulated heat for the pre-heating of inlet polluted ...
-
Manufactured by Cematekbased in ITALY
The advantage of catalytic combustion, when compared to the thermal one, is to guarantee the complete oxidation of volatile organic substances at relatively low temperatures, usually 320-450°C. The low combustion temperature, as well as allowing less energy consumption, ensures a negligible production of NOx, a pollutant thet in ...
-
based in GERMANY
Lower operating costs than conventional thermal oxidation systems by lowering the oxidation temperature necessary for the combustion reaction by means of noble metal catalysts. Ideal for use with unproblematic exhaust air streams (without any catalyst poisons) and pollutant concentrations between 2-10 g / ...
-
Manufactured by ITI Engineeringbased in ITALY
Combustion plant for wood waste. The plant is basically made up of a hot gas generator combined with a direct drum dryer, for MDF panel production, and a thermal oil boiler for heating the oil needed for the press ...
-
Manufactured by ITI Engineeringbased in ITALY
Combustion plant for wood waste. It consists mainly of a hot gas generator coupled with a thermal oil boiler, for the heating of the oil required for indirect heating dryers and plywood production presses, and the indirect saturated steam generators for a belt dryer for the production of particleboard panel, and superheated for the ...
-
Manufactured by WEHRLEbased in GERMANY
In terms of incineration plants, WEHRLE is the specialist regarding fluidised-bed ...
-
Manufactured by Leverage Incorporated NVbased in BELGIUM
Fuel gas/liquid skids for combustion plants : it is a modular unit complete with piping, supports, tubing, valve assemblies, filters, instrumentation, wiring on board and junction boxes. Engineering department develops detailed engineering starting from basic information and technical specifications complying with the main international ...
-
Manufactured by Linka Energy A/Sbased in DENMARK
A biomass plant based on wood pellets consists of a silo, which are made from either fibreglass for outdoor installations or fibreboard for indoors. The pellets are transported from the base of the silo by an auger to the boiler room, directly to a cell sluice and then into the boiler’s combustion hearth. When the boiler ...
-
Manufactured by Linka Energy A/Sbased in DENMARK
A combustion plant based on wood chips consists of a scraper unit, which is sensibly located near the storage. 3 horizontal scrapers are positioned in the storage area which feed the chips to a sunken auger at the end of the scraper system. This auger is monitored by a photo cell. Whenever the auger is not filled, hydraulic cylinders will ...
-
Manufactured by Conveco S.r.l.based in ITALY
High efficiency, compact biogas suction and combustion unit mounted on a frame. Compact design and easy installation allow use in emergency situations, for temporary installations or to check the production capacity of the ...
-
based in FINLAND
We have got WID compliant boilers for the C grade waste wood and SRF combustion: Our WID compliant waste wood gasification boiler manufacturer has over 60-years experience, Works with really low-quality wood, MDF, and chipboard based biomass, and waste wood, SRF combustion is possible together with biomass (80/20% ratio), Waste wood ...
-
Manufactured by Körting Hannover AGbased in GERMANY
Climate protection and plant efficiency; Lack of resources and progressively increasing fuel prices – Climate protection and stricter environmental specifications. These are just a few of the challenges for which future economical solutions in the area of firing technology are required. The efficiency of technical firing plants ...
-
Manufactured by Lekea - Dan Trim ApSbased in DENMARK
A hydraulic floor scraper is normally used with woodchips. The woodchips are loaded in a container, and the floor scraper will automatically push the woodchips to the cross screw where strong screws will convey the fuel into the combustion ...
-
Manufactured by Lekea - Dan Trim ApSbased in DENMARK
A hydraulic floor scraper is normally used with woodchips. The woodchips are taken to the store room, and the floor scrapers will automatically push the woodchips into the cross screw where strong screws will convey the fuel into the combustion ...
-
based in GERMANY
ECOTUBE® is a system which is at any time possible to be integrated into an existing plant. The ECOTUBE® is a secondary air tube which can be additionally added, primarily for grate fired combustion including WTE-plants, which as well as an improvement in flow patterns in the chamber can also inject a determined amount of secondary ...
-
Manufactured by IBS Industrie-Brenner-Systeme GmbHbased in GERMANY
Modular designed system for direct heating of process air for dryer and post combustion plants. GRIDFIRE-moduls are available in straight, T- and X-shape for capacities starting at 160 kW. The combination of the moduls makes burner capacities up to 25 MW and more ...
-
Manufactured by Cochran Ltdbased in UNITED KINGDOM
Cochran’s ST37 Package Steam Boiler is of horizontal three pass wet back design and constructed in accordance with BS EN 12953. This CE marked boiler is designed to meet the latest European environmental legislation and Medium Combustion Plant Directive (MCPD). Suitable for any application, the design features Cochran’s low NOx, ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you