Elevated Flare (Flares) Equipment Available In Canada
-
Manufactured by Puti Energybased in INDIA
Sonic Flare , Portable Flare ,Smokeless,low noise , low- Brightness Flares we supply . With Economic and Robust structures like Derrick,Guy-roped and Self supported . Designed specifically to suit local structural laws and emission laws. Clean Flare technology which we have achieved and refining it with our every installation.We ...
-
Manufactured by Alliance Thermal Engineersbased in INDIA
Flare systems can be classified according to: Structural Support: Self Supporting, Guy Wired, Derrick Guy Wired, ...
-
based in UNITED KINGDOM
This range of simple elevated flares is typically used for short term applications (such as gas pumping trials) or those where exhaust gas emissions are not subject to regulation. The combustion process is visible and the combustion temperature is not ...
-
Manufactured by Ennovobased in AUSTRALIA
Our elevated flare range of open flare stacks provides a good degree of control over the combustion process in an elevated flame burner, whilst remaining highly flexible and portable. They are ideal for temporary or emergency mobile systems on landfill sites, or can be used at sewerage treatment works and other anaerobic ...
-
Manufactured by DWS BVBAbased in BELGIUM
As one of the most used elevated flares around the world, our flare owes its popularity to its robustness, reliability, and durability. Just like our other flares, the elevated flare is designed to work consistently at ambient temperatures varying from -15 °C to +45 °C. No weather ...
-
Manufactured by Fives I.T.A.S. s.p.a.based in ITALY
Elevated flares are vertical stacks used to dispose of waste gases through combustion; the “flare tips” (flare burners) are located at the top, which ensures personnel, plant and environment safety. ITAS elevated flares range from low-investment small utility stacks up to the tallest ...
-
Manufactured by BD Environmental Solutionsbased in USA
Utility Flares; Pipe Flares are unassisted equipment designed to combust hydrocarbons where non-smokeless operation is environmentally acceptable or where the waste gases produce little or no smoke due to their ...
-
Manufactured by Flare Products Limitedbased in UNITED KINGDOM
At the top of the elevated system is the flare tip and pilot/ignitor system. The flare tip is sized according to the flow rate and is manufactured from 304 stainless steel. The larger diameter is the windshield which helps stabilise the flame. Located adjacent is the pilot/ignitor tip. This is made in 304 stainless steel and contains the ...
-
Manufactured by Conveco Srlbased in ITALY
The T flare is a self-supported elevated flare (open type) complete with a safety ladder and an upper platform that allow access to the nozzle and ignition and flame control equipment. The flame shield is designed to prevent accidental flame extinguishing and provides a chamber lined with fiberceramic for more complete biogas combustion. The ...
-
Manufactured by BD Environmental Solutionsbased in USA
High gas flows and difficult access to digesters may cause a need for a deviation from the standard design of biogas flares, which are used to dispose of waste streams coming from landfills, biogas, biomass and wastewater facilities. Enclosed flares are designed to maintain a high destruction ratio within the vertical combustion ...
-
Manufactured by Airoil Flaregas Pvt. Ltd.based in INDIA
Optimization of an Elevated Staged Flare for a Large Refinery or a Gas Plant. In recent years most of the refineries, petrochemicals & gas processing plants are seen to be of larger capacities. Flare system for such plant are required to operate at two extreme flow conditions, one very high flow rates (in excess of 1000 tons per ...
-
Manufactured by Encore Combustionbased in USA
Most common flare design. Include flame retention device(s) to maintain stable combustion. Used when waste vapor is inherently smokeless or for emergency relief scenarios. No assist method or utility requirement. To reduce purge gas usage, a purge seal is ...
-
Manufactured by Encore Thermoengineering S.R.L.based in ITALY
Derrick structure (demountable type if requested) can be the optimum solution for Flare Systems installed inside plants, when higher elevation is required to limit ground radiation and available area is limited as a result of other present equipment. The height of this type of flare can be even more than 200 ...
-
Manufactured by Europem N.Vbased in BELGIUM
Industries will generate Low CV waste gases, which are either difficult to burn or can contain insufficient energy to self-sustain the combustion process. For these applications, Nutara developed the proprietary "ring-of-fire" Flare Tip. This tip has a ring of flame around the central waste gas tip thus ensuring complete oxidation of the ...
-
Manufactured by Europem N.Vbased in BELGIUM
Since the 1980’s, key staff of Europem have been responsible for the design, fabrication, installation, commissioning and maintenance of numerous flare systems including some of the most stringent and demanding applications.Europem’s extensive experience in flare design has resulted in a comprehensive range of elevated and ground ...
-
Manufactured by Europem N.Vbased in BELGIUM
Since the 1980’s, key staff of Nutara have been responsible for the design, fabrication, installation, commissioning and maintenance of numerous flare systems including some of the most stringent and demanding applications. Nutara designs are optimized towards flexibility, robustness, low emissions, high thermal efficiency and ...
-
Manufactured by Europem N.Vbased in BELGIUM
Air assisted flares enable the smokeless combustion of low pressure waste gases. Air (or Gas) assisted flares can be used when no steam is available on site. Air assisted flares use forced draft Air or Gas to create turbulence ensuring that sufficient primary combustion air is supplied to the flame. The amount of air and hence the size of the ...
-
Manufactured by Europem N.Vbased in BELGIUM
Utility Flares (Pipe Flares) are the most basic flare design available, to provide a robust, reliable and flexible solution for the flaring of large volumes of low pressure waste gas when smokeless operation is either not required or can be achieved without an assisting medium (like steam, air or gas). Reliable operation at both ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
The Ghost series of enclosed biogas flares is a simple and cost effective combustion solution for a variety of applications where a hidden flame is required. The superior design, high quality stainless steel construction and unmatched versatility make the Ghost Series Enclosed Flares an exceptional choice for emissions control within the ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
The Momentum Biogas series of elevated flares is our most economical line of combustion equipment for the biogas sector, offering a cost-effective solution with rapid delivery. Momentum flares utilize a specially designed “burner and shroud” system to manage the intricate mixing with ambient air to provide a high DRE (98%) and ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you