Plate Heat Exchangers Equipment For Energy Management In Australasia
-
PremiumManufactured by HRS Heat Exchangers Ltd.based in UNITED KINGDOM
HRS Gasketed Plate Heat Exchangers are manufactured as standard from either AISI 304/316 stainless steel or titanium to a thickness of 0.6mm, although plate thickness options of 0.8mm or 1.0mm are also available if required. The exchangers are fitted with EPDM or NBR gaskets with the frames constructed from painted carbon steel. A double seal arrangement around the two ports ensures that if fluid ...
-
PremiumManufactured by HRS Heat Exchangers Ltd.based in UNITED KINGDOM
The HRS Brazed Plate Heat Exchanger range works on the same principle as conventional plate heat exchangers, but consists of a pack of corrugated plates joined together and sealed by furnace brazing. Typically the units are copper brazed, however for applications where the medium is aggressive to copper, or for where temperatures range from 225°C to 400°C, then nickel is used. The plates ...
-
Manufactured by Clarke Energybased in UNITED KINGDOM
The GE Jenbacher container is a high quality unit which can be deployed where economical and speedy installation is required. The GE Jenbacher containers are fully tested when they leave the production facility and are excellent for plug-and-play applications. The overall compact design ensures a space saving installation with service-orientated ...
-
Manufactured by Güntner U.S. LLC.based in USA
Perfectly chambered plate/gasket construction for high pressures of up to 63 bar. Six possible gap types (combined). Many years of experience in designing refrigerant equipment. NH3/CO2 cascade applications. Low refrigerant filling quantity/high power density. Cleaning at 50 bar ...
-
Manufactured by INOX Pty. Ltdbased in AUSTRALIA
The tunnels are fully manufactured from 304 SS and have been designed for washdown food production ...
-
Manufactured by Muntersbased in USA
Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The continuous fold construction of Z-Duct reduces or ...
-
Manufactured by Muntersbased in USA
Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The continuous fold construction of Z-Duct reduces or ...
-
Manufactured by Güntner U.S. LLC.based in USA
The spectrum of thermoline's plate heat exchangers encompasses a diverse and variable range of gasketed and module welded versions with an excellent price-performance ration. Both designs are produced by thermowave in the most varying plate sizes as well as individually required materials. Users can achieve a high degree of flexibility and investment protection, as their apparatuses can be ...
-
Manufactured by Evapco Inc.based in USA
The Evapcold packaged chiller product line consists of 50 models. Each is completely self-contained and has a very low ammonia charge of less than 1.0 lb per TR. Evapcold units come with several optional features and accessories that make them a truly innovative solution for your refrigeration needs. The chiller provides a chilled secondary fluid (glycol) to the refrigeration load, which ...
-
Manufactured by Clarke Energybased in UNITED KINGDOM
Cogeneration (cogen) through combined heat and power (CHP) is the simultaneous production of electricity with the recovery and utilisation heat. Cogeneration is a highly efficient form of energy conversion and it can achieve primary energy savings of approximately 40% by compared to the separate purchase of electricity from the national electricity grid and a gas boiler for onsite heating. ...
-
Manufactured by Windsor Engineeringbased in NEW ZEALAND
Crossle Coils manufacture a wide range of Hot Water or Thermal Fluid Heat Recovery Coils. A Heat Recovery Coil is principally designed to Extract normally expelled heat from a Flue Gas Stream or a Hot Air Stream and to utilise the recovered heat for pre-heating the boiler feed water, heating water for wash down purposes or process heating. Thermal Fluid can be circulated through a Heat Recovery ...
-
Manufactured by Güntner U.S. LLC.based in USA
Corrosion resistant. Fail-safe operation. Six possible gap types (combined). Compact design, low space requirements. Capacity can be adjusted by adding or removing plates. Excellent fouling resistance due to high turbulence and smooth surfaces. Food-safe materials. Product-friendly design. Reliable ...
-
Manufactured by Muntersbased in USA
The Thermo-Z plate style heat exchanger is designed to recover heat from energy consuming processes up to 1500°F. Energy can be recovered and returned as process make-up air, used to preheat combustion air, or used for plant or office heating. Thermo-Z offers fully adjustable plate thickness and spacing as well as multiple flow patterns. The heat exchanger is designed for industrial ...
-
Manufactured by Muntersbased in USA
Des Champs heat exchangers offer designs utilizing plate counterflow heat exchangers, heat pipe, and energy recovery wheels. These heat exchangers form the backbone of many system configurations and can be configured with unique traversing frost prevention. Des Champs heat exchangers have been used everywhere from the hottest climates to ...
-
Manufactured by Clarke Energybased in UNITED KINGDOM
A GE Jenbacher gas engine module is configured for the recovery of both electricity and heat via a cogeneration / CHP configuration. As with the genset, the gas engine is linked to the alternator which produces electrical power for export. The cooling water circuits of the engine are first linked to a plate heat exchanger which facilitates the transfer of hot water to an external hot water ...
-
Manufactured by Muntersbased in USA
Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The continuous fold construction of Z-Duct reduces or ...
-
Manufactured by Muntersbased in USA
Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The continuous fold construction of Z-Duct reduces or ...
-
Manufactured by Muntersbased in USA
Adding Z-Duct allows for the introduction of more outdoor ventilation air without overloading the HVAC system. Z-Duct plate heat exchangers offer multiple flow configurations, have extremely low-leakage and high energy-transfer. Pressure drop is minimized and heat-transfer maximized by dimples in the plates which separate the plates. The continuous fold construction of Z-Duct reduces or ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you