Francis Hydro Turbines Equipment For Hydro Energy In USA
-
Manufactured by Nautilus LLCbased in USA
The T Ultra Low Head turbine (T-ULH) is the most powerful open flume turbine built by Nautilus. This unregulated design produces from 500 watts to 3,300 watts with a head range from 1m to 3.7m. Often two or three units are installed to match streamflow variation or the T-ULH is installed in combination with the Regulated CMC. For large open flume environments, where it is not possible to drain ...
-
Manufactured by HydroTech Engineering, LLCbased in USA
HTE Engineering and its partners have provided hundreds of Francis turbines all over the world, ranging in size from 145 kW to 750 MW. The Francis turbine is a type of inward-flowing reaction turbine. This turbine is named after James B. Francis (1815 – 1892), an American hydraulic engineer who designed, built, and tested the first of these types of ...
-
Manufactured by Nautilus LLCbased in USA
The regulated CMC Ultra Low Head turbine (CMC-ULH) operates in a similar power range as the 660-ULH in an open flume and produces up to 1500 watts. The CMC offers better part gate regulation and efficiency than the other cylinder gate Nautilus ...
-
Manufactured by Gilbert Gilkes & Gordon Ltdbased in UNITED KINGDOM
Gilkes Francis Turbines are available as either horizontal or vertical units. The water enters the spiral, or scroll case, and is directed by a series of moveable guide vanes, or wicket gates, to the turbine runner. As the water passes through the runner it rotates and the water pressure drops. Water is then discharged through a draft tube into the tailrace. Flow is controlled by opening or ...
-
Manufactured by Flame Spray SpAbased in ITALY
Caboflam H trademark identifies Flame Spray's technological processes for carbide coatings in metallic matrix through high-pressure combustion equipment (HP/HVOF). These types of coatings exhibit excellent bond strength, higher micro hardness and density than those produced with traditional detonation equipment. Solids contained in water cause wear on critical components, such as needle valves ...
-
Manufactured by WWS Wasserkraft GmbHbased in AUSTRIA
The Francis turbine – also know as “excess pressure turbine” – is usually installed for medium heads of water and constant water quantities. This type of turbine mostly uses a steel spiral turbine, since there is often a tube line leading to the turbine at heads of water over 20m. Further advantages of the compact design of the spiral turbine are much lower construction ...
-
Manufactured by Tenmat ltdbased in UNITED KINGDOM
FEROFORM T814 is a composite material made from woven fibre bonded with resin with PTFE as a friction ...
-
Manufactured by Mavel a.s.based in CZECH REPUBLIC
Runner Diameters 1000 mm to 2500 mm. Head Range Up to 300 meters (1000 feet). Flow Range Up to 35 cms (1236 cfs). Power Output Up to 30 MW. Transmission Runner Assembled to Generator or Turbine ...
-
Manufactured by Canyon Hydrobased in USA
Canyon Hydro designs and manufactures small hydro systems ranging from 4kW to 25MW. Each system is designed and built at our manufacturing facilites in the USA. For our customers with residential or small community projects, Canyon Hydro provides a broad selection of micro-hydro systems up to about 100kW, each delivering high efficiency, quality and reliability at a reasonable cost. If you have ...
-
Manufactured by VAPTECH Ltdbased in BULGARIA
Either standardized units for small hydro or tailor-made solutions, VAPTECH is delivering high-quality Francis turbines. VAPTECH’s care for maximum efficiency and resistance to cavitation is guaranteed by flow dynamic analyses and tests from leading European research ...
-
Manufactured by Nautilus LLCbased in USA
The Nautilus CMC Medium Head (CMC-MH) style turbine has been produced in the U.S. since the early 1900’s. This simple regulated Francis turbine is designed for heads of 3m to 12m and develops a maximum electrical output from 1,900 watts to 9.2 kw, depending on available ...
-
Manufactured by Piedmont Hydro Technologies LLC. (PHT)based in USA
PHT specializes in small hydro control systems. We integrate commercially available components from trusted names, with custom software and programming specific to each plant, to provide reliable, cost-effective solutions. Standard features reduce cost and save time, while ensuring all aspects of your plant work together for optimal results, from under 100kW, to over 10 MW. PHT’s proven PLC ...
-
Manufactured by HydroTech Engineering, LLCbased in USA
With over 50 years in the industry, HTE Engineering and its partners have provided Kaplan turbines ranging in size from 200 kW to 400 ...
-
Manufactured by Nautilus LLCbased in USA
The 660 Ultra Low Head turbine (660-ULH) is a 150mm (6in) diameter Francis turbine with a bronze runner and bronze and stainless steel guide vane and gate assembly. It uses a water lubricated rubber bearing below water and heavy duty spherical roller bearings above water to support the shaft and pulley assembly. The turbine case is fitted with an adjustable cylinder gate to turn the unit off and ...
-
Manufactured by Gilbert Gilkes & Gordon Ltdbased in UNITED KINGDOM
The Turgo Impulse turbine was developed by Gilkes to be a simple impulse type machine with a higher specific speed than a Pelton. The design therefore allows a larger jet of water to be directed at an angle onto the ...
-
Manufactured by Wagstaff Applied Technologies - a division of Wagstaff, Inc.based in USA
Wagstaff Applied Technologies provides reconditioning services for Francis, Kaplan, Pelton, and other turbine runners. Wagstaff AT performs welding operations per AWS or ASME codes, using an established suite of welding procedures. Runners are typically machined on our CNC horizontal boring machines. Wagstaff AT inspects machined parts utilizing the latest in inspection tool technology. In ...
-
Manufactured by Nautilus LLCbased in USA
The Nautilus T Medium Head turbine has been manufactured for over 10 years. Many of these turbines are installed in the U.K. and the United States. The hydraulic design is based on a utility grade Francis turbine that is reduced in size and fitted with a trapezoidal section scroll ...
-
Manufactured by Mavel a.s.based in CZECH REPUBLIC
Runner Diameters 400 mm to 1400 mm. Head Range 15 to 300 meters (50 to 1000 feet). Flow Range 0.5 to 20 cms (18 to 706 cfs). Power Output 100 kW to 12 MW. Transmission Runner Assembled to Generator or Turbine ...
-
Manufactured by The James Leffel & Companybased in USA
Unit 1: 0.66 M Francis 2.0 MW / 82.2 M Head / 750 RPM. Unit 2: 0.47 M Francis 1.0 MW / 82.2 M Head / 1000 ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you