Kaplan Hydro Turbines Equipment For Hydro Energy
-
Manufactured by Mavel a.s.based in CZECH REPUBLIC
Runner Diameters 1050 mm to 5500 mm. Number of Runner Blades 3 or 4. Head Range 1.5 to 12 meters (5 to 39.5 feet). Flow Range 15 to 150 cms (530 to 5340 cfs). Power Output 400 kW to 8 MW. Transmission Belt Drive or Parallel ...
-
Manufactured by Litostroj Powerbased in SLOVENIA
Design principle and range of use: Kaplan turbine is a double-regulated turbine. It is equipped with a Kaplan runner with variable-pitch blades that is hydraulically optimized for a wide range of discharge and a relatively wide range of head and is combined with regulated guide vanes, which makes a Kaplan turbine suitable for a wide range of discharge and head. The governor enables optimizing the ...
-
based in CANADA
Edmunston energy's vertical Kaplan power station had a worn components and was out of alignment. The entire dam had settled and the unit was no longer plumb. CME documented dismantling under our specialists' experienced supervision. We determined that the cause of out of plumb was settling of the dam itself. We removed and serviced worn bearings, repaired shaft areas, did weld repair of ...
-
Manufactured by Ganz Engineering and Energetics-machinery Manufacturer Ltdbased in HUNGARY
Adjustable guide vane ring for changing the water amount. The stainless steel guide vanes are powered by carbon steel levers with safety sliding clutches. The guide vanes rotate in maintenance-free pins, which are in the turbine covers with stainless steel protection. If necessary, they are equipped with a guide vane adjusting system, this ensures good efficiency in a wide operating ...
-
Manufactured by CINK Hydro - Energy k.s.based in CZECH REPUBLIC
Low-head, double-regulated Kaplan turbines. With compact structure and minimum requirements on excavation and civil works. Easily maintained, with long service life and high efficiency across the entire operation range (20% - 100% of design flow). Penstock-ready and available in four different layouts to suit the needs on every low-head dam or run-of-the-river ...
-
Manufactured by CKD Blansko Holding, a.s.based in CZECH REPUBLIC
Since 1904 CKD Blansko has manufactured more than 427 Kaplan turbines and they operate at 111 sites. Their total output amounts more than 5346 MW. We provide horizontal or vertical, spiral or flume arrangement, bulb, pit or S-type with fixed or regulated blades and/or wicket gates. All types of Kaplan turbine used for operation within the range shown in the Q/H diagram. Runner diameter up to 10 ...
-
Manufactured by Harbin Electric Machinery Company Limitedbased in CHINA
The types of hydro turbines we produced include: Francis, Kaplan, Bulb, Pump-Storage, Deriaz, Pelton and Huge Pump. The max dia of runner for Francis and Kaplan are 10.4m and the producing technology reaches to an international advanced level. The types of hydro turbines we produced include: Francis, Kaplan, Bulb, Pump-Storage, Deriaz, Pelton and Huge Pump. The max dia of runner for Francis and ...
-
Manufactured by MJ2 Technologie sasbased in FRANCE
The permanent magnet variable-speed generator is directly coupled to the turbine. It has an external rotor. The stator windings are assembled on a fixed shaft in central ...
-
Manufactured by Guangzhou Electway Technology Co., Ltd.based in CHINA
It is widely used in hydro power stations with the head of 6--30 meters. It is suitable for hydro power resource of low water head and high flow, there are two types: fixed blade. and adjustable blade type. The fixed blade type is suitable for hydropower station with small capacity, the range is between 70. to percent, the adjustable blade type is larger with range between 30 to 100 percent. We ...
-
Manufactured by WWS Wasserkraft GmbHbased in AUSTRIA
This type of turbine is primarily suitable for low pressure areas and large quantities of water. The head of water (1m to 40m) determines the number of blades on the rotor (3 to 6 blades). WWS supplies Kaplan turbines with vertical design with concrete or steel spirals as well as tube turbines – individual according to the requirements of your power plant. If possible, direct drive for the ...
-
Manufactured by Gamesa Electricbased in SPAIN
The hydroelectric sector is characterised by a high level of customisation, as each power station must be optimised according to the hydroelectric resource available and the configuration of the installation. ...
-
Manufactured by Mavel a.s.based in CZECH REPUBLIC
Runner Diameters 1050 mm to 2500 mm. Number of Runner Blades 3 or 4. Head Range 1.5 to 12 meters (5 to 39.5 feet). Flow Range 5 to 45 cms (180 to 1590 cfs). Power Output 100 kW to 3 MW. Transmission Direct Drive, Belt Drive or Bevel ...
-
Manufactured by MJ2 Technologie sasbased in FRANCE
The permanent magnet variable-speed generator is directly coupled to the turbine. It has an external rotor. The stator windings are assembled on a fixed shaft in central position. They are ventilated and refrigerated by contact with the water flowing around the bulb and by fans. The rotor is equipped with permanent magnets, and is solid with the turbine runner. The magnets are assembled at the ...
-
Manufactured by ClearPower North Americabased in USA
When electricity is applied to a magnetic fan motor it makes the fan spin, but did you know the reverse also true? If you spin the fan blade backwards it produces electricity. Water pressure is energy, and by using the pressure and flow created by gravity found in places like common water pipes to spin the fan, it transforms the simple water pipe into a generator. The flowing water becomes the ...
-
Manufactured by Zeco Di Zerbaro & Costa & C. S.r.lbased in ITALY
Represents the evolution of Kaplan turbine, developed to reduce civil works and the enviromental effects in HPP. Power from 80 kW up to 2 MW Horizontal or vertical ...
-
Manufactured by Joint-Stock Company `Tyazhmash`based in RUSSIA
Hydraulic turbines for Ust-Khantaiskaya HPP, Kurejskaya HPP, Serebrjanskaya HPP, Teriberskaya HPP are performed in northern variant. The turbine for Nizhne-Teriberskaya HPP is manufactured with usage of the materials, resistant to marine ...
-
Manufactured by Reivax North America, Inc.based in CANADA
The RVX Power Speed Governor System was developed for speed and power control of turbines. Besides speed regulation, they can perform all the supervision, command and automation functions required for power generation turbines. The speed governor RVX Power system can be fully customized to meet the most demanding requirements. Reivax can supply a turnkey solution or individual components, ...
-
Manufactured by VAPTECH Ltdbased in BULGARIA
The axial turbines are designed for projects with low and very low heads with a strong flow variation. VAPTECH offers mainly the classic vertical shaft Kaplan turbine with 3 to 6 runner blades and with double regulation. For runner diameters up to 1400 mm we use a steel spiral casing and for bigger runner diameters we recommend a concrete spiral casing. Our solution and advice is for a direct ...
-
Manufactured by Litostroj Powerbased in SLOVENIA
Design principle and range of use:Pit and Bulb turbines are horizontal axial flow units equipped with a regulated Kaplan runner. These turbines are typically used at low heads (1,5 m to 25 m) and high discharges. The double regulation design allows wide operating range covering various heads and discharges. ...
-
Manufactured by Hydrohrom, s.r.o.based in CZECH REPUBLIC
Runner and guide wheel regulation. Designed as a monoblock, and is used primarily in reconstructions of older plants. Guide wheel performs the function of both the operational and closure system which is controlled by gravity or hydraulic pressure accumulator. Installation is either with transfer belt or with a direct connection to the ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you