Hydro Energy Equipment

Variable and fixed displacement types. SAE mounting, spline shafts. Typical operating pressures up to 5000 psig (350 bar). High-speed operation. High starting torque efficiency. Different sizes for different applications. Suitable for open and closed loop circuits. Supply includes overrunning clutch.

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Engine Starter Product line

Operates on any pressurized gas (0-220 psig). Break-away torques up to 3,700 ft lb. Output speeds up to 12,000 RPM. For industrial gas turbine or reciprocating engines. Standard and custom interfaces available. Helical rotor design. Positive displacement. Roller-ramp overrunning clutch to pre-engage the starter to the turbine. Dynamically ...

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Engine Starter Product line

24 volt DC power. Solenoid actuated Positork drive. Output torque up to 80 ft lb. Splined output for gas turbine applications. SAE 3 mounting flange, multi-position. CW and CCW direction of rotation.

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Engine Starter Product line

In a steam generator vessel or pressurized water reactor (PWR) plant, the reactor core heats water without boiling, and exchanges heat with a lower pressure water system, which will then turn to stream to power the turbine. The Peerless brand Secondary Separator within Nuclear Steam Generator Vessels (Pressurized Water Reactor Plants) or ...

By CECO Environmental based in Dallas, TEXAS (USA). from CECO Peerless - Nuclear Power Separators Product line

The H3 Power Unit is Hilliard's most advanced brake control system. With a PID Loop Control, the BBH3 Power Unit is capable of monitoring speed. The Hilliard BBH2 Power Unit incorporates an engineered hydraulic circuit to control the brake torque during a typical stop. Large capacity hydraulic accumulators provide additional volume for precise ...

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Braking Systems - BrakeBoss Product line

The Hilliard BBH2 Power Unit incorporates an engineered hydraulic circuit to control the brake torque during a typical stop. Large capacity hydraulic accumulators provide additional volume for precise control of brake pressure. Equipped with manual overrides and hand pump for power outages, high pressure filtration and control braking mode to meet ...

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Braking Systems - BrakeBoss Product line

The A400 is an arm style caliper brake designed to accept a large selection of Hilliard thrusters. These thrusters include spring applied hydraulic released, spring applied pneumatic released, hydraulic applied spring released, and pneumatic applied spring released. The 400 requires a minimum disc diameter of 24' and is offered in 2 sizes to ...

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Braking Systems - Caliper Brakes Product line

The A300 is an arm style caliper brake designed to accept a large selection of Hilliard thrusters. These thrusters include spring applied hydraulic released, spring applied pneumatic released, hydraulic applied spring released, and pneumatic applied spring released. The A300 requires a minimum disc diameter of 12' and is offered in 4 sizes to ...

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Braking Systems - Caliper Brakes Product line

The Hilliard M400HS brake caliper is a hydraulic applied, spring retracted brake caliper for use in heavy duty industrial applications. The brake caliper is suitable for outdoor applications and has been designed for use in many different extreme environments. The M400HS brake caliper is capable of producing a maximum 12,960 lbf (57.6 kN) of ...

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Braking Systems - Modular Brakes Product line

The Hilliard High-Speed Starter Overrunning Clutch Drive provides positive engagement and high torque on demand. Featuring a unique roller-ramp design, the clutch when engaged transmits power via the precision-machined cam and roller assembly connected to the input shaft. A ball bearing at each end of the roll cage supports and aligns the cam in ...

By Hilliard Corporation based in Elmira, NEW YORK (USA). from Engine Starter Product line

Meets JIC Standards, 5 to 15 Horsepower, 500 to 900 PSI, 60 Gallon Reservoir, 10 to 20 GPM.

By Shand & Jurs (L&J Technologies & L&J Engineering) based in Hillside, ILLINOIS (USA). from Combustion Controls Product line

A boiling water reactor, or BWR, is a nuclear reactor used to produce electrical power. Its reactor core heats the water, which then turns to steam to power a steam turbine. The Peerless brand Secondary Separator within Nuclear Reactor Vessels (Boiling Water Reactor Plants), or “steam dryer”, is used as the final stage of water ...

By CECO Environmental based in Dallas, TEXAS (USA). from CECO Peerless - Nuclear Power Separators Product line

The SpectrOil M/F-W has become the standard instrument when on-site and immediate fuel analysis is a necessity. It fulfills the requirements of ASTM D 6728, Standard Test Method for Determination of Contaminants in Gas Turbine and Diesel Engine Fuel by Rotating Disc Electrode Atomic Emission Spectrometry.

By Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA). from Other Fluid Analyzers Product line

Ten Gallon Reservoir Eliminates the Need for Heat Exchanger, Pressure, Filter, and Level / Temperature Switches, Meets JIC Standards, 3.7 GPM, 100 to 300 PSI.

By Shand & Jurs (L&J Technologies & L&J Engineering) based in Hillside, ILLINOIS (USA). from Combustion Controls Product line

Double end, low by-pass leakage, 1 1/2' - 8' bore, bronze bearings, up to 1500 lbs, chrome plated cylinder rod, foot, flange, or pivot mounting.

By Shand & Jurs (L&J Technologies & L&J Engineering) based in Hillside, ILLINOIS (USA). from Combustion Controls Product line

ORC technology is based on the widely known and proven Rankine Cycle principle. It was named after William John Macquorn Rankine, a Scottish polymath and Glasgow University professor. The Rankine cycle is a cycle that converts heat into energy. The heat is supplied externally to a closed loop.

By Inciner8 Limited based in Southport, UNITED KINGDOM. from Waste to Energy Product line

The hydraulic power pack can be used in rescue vehicles, demolition equipment, mining machinery and hydraulic supports, test rigs, etc. Full utilization of all hydraulic equipment on site in case of mobile independent kit Neròn can supply a powerful power pack with gas engine. The gas engine will supply to the hydraulic pump the oil to run ...

By Neron Pumps based in Ranica, ITALY. from Hydraulic Power Pack Product line

Transducer for the conversion of the difference in phase angle from two electrical systems requiring synchronization into a direct current or voltage signal which is proportional to the measured value.

By Camille Bauer Metrawatt AG based in Wohlen, SWITZERLAND. from Unifunctional Devices - Power Factor, Phase Angle, Phase Angle Difference Product line

Variable frequency drives (VFDs) at hydroelectric power plants often control critical systems such as irrigation, water levels, fish management devices or flood gate control systems. In many cases the VFDs may already be equipped with manufacturer-installed line side surge protective devices (SPDs) to protect against spikes generated by switching ...

By Raycap based in Maroussi Athens, GREECE. from Energy/Utilities - Renewable Energy Product line

The new range of the Landustrie screw pump covers the hydropower screw turbines. An efficient use of water power is already achieved at a level difference of 1 meter and a capacity of 500 l/sec. The largest capacity and level difference for hydropower screws is as much as 15000 l/sec. at 10 meter.

By Landustrie Sneek BV based in Sneek, NETHERLANDS. from Hydropower Product line