Hydraulic Generator Equipment
-
Manufactured by Egersund Markleenbased in NORWAY
Markleen can supply hydraulically driven electricity generators in a variety of power ...
-
Manufactured by Pumptech ASbased in NORWAY
DYNASET HG Hydraulic Generator converts the hydraulic power of a mobile machine into electricity. HG Hydraulic Generators produce high quality electricity from 3,5 kVA up to 350 kVA for 50 or 60 Hz frequencies to power any electric appliance in mobile ...
-
Manufactured by Chengdu Forster Technology Co., Ltd.based in CHINA
by Forster in China. Forster has replaced a brand-new hydraulic turbine, generator and control system, and the output power of a single unit has been increased from 150KW to ...
-
Manufactured by Chengdu Forster Technology Co., Ltd.based in CHINA
up to 10MW per unit. It has a very high degree of efficiency of more than 95 % and is an ubiquitously applicable turbine type. Foster Francis turbine is a complete set of hydroelectric generating units, including valve, governor, control system and ...
-
Manufactured by Turolla - Danfoss Power Solutions S.r.l.based in ITALY
ezePower is the Turolla hydraulic motor-powered electrical generator for use in mobile equipment applications. The generator produces a small amount of electrical power in areas of a machine that are too difficult, too costly, or too dangerous to run electrical wiring to. ezePower eliminates dependency on wires across troublesome ...
-
Manufactured by HS DYNAMIC ENERGY CO.,LTD.based in HONG KONG
Francis turbine is one of the most widely used turbines, HS Dynamic Energy’s Francis turbines are commonly used at hydraulic head range of 6-500 meters, all our Francis turbine generator offer vertical type and horizontal type ...
-
Manufactured by HS DYNAMIC ENERGY CO.,LTD.based in HONG KONG
Francis turbine is one of the most widely used turbines, HS Dynamic Energy’s Francis turbines are commonly used at hydraulic head range of 6-500 meters, all our Francis turbine generator offer vertical type and horizontal type ...
-
Manufactured by HS DYNAMIC ENERGY CO.,LTD.based in HONG KONG
Turgo turbine(inclined jet turbine), the water flow output from nozzle flows along a certain angle to push the water wheel, and the water flow goes inside the blades from one side and goes out the blades from another side, our turgo turbine is applicable for micro-sized, small-sized and medium-sized power station. all our Turgo turbine ...
-
Manufactured by HS DYNAMIC ENERGY CO.,LTD.based in HONG KONG
Francis turbine is one of the most widely used turbines, HS Dynamic Energy’s Francis turbines are commonly used at hydraulic head range of 6-500 meters, all our Francis turbine generator offer vertical type and horizontal type ...
-
Manufactured by HS DYNAMIC ENERGY CO.,LTD.based in HONG KONG
Pelton turbine generator is suitable to meet micro-sized, mini-sized and Small-sized hydropower project, and it’s efficiency is higher than turgo turbine, usually from 80%-89%, it is applicable for the hydraulic head range of ...
-
Manufactured by Schwerdtel GmbHbased in GERMANY
If you want to feed from 200 liter drums.In this case we recommend a press type S6-F with pressure generated by hydraulic unit, or pressure generated pneumo-hydraulically type S6-F/PH. The pressure plate moves into the drum and presses on the surface of the material. The material is fed through an outlet hole in the pressure ...
-
Distributed by Haulmark Equipment Ltd.based in UNITED KINGDOM
Haulmark Equipment is the main dealer for Dynaset hydraulic magnet generator. This is a quick release unit which can be hooked onto an excavator"s dipper arm or attachment. Hydraulic supply is provided from the excavator"s hammer ...
-
Manufactured by Ferrari International 2 S.p.A.based in ITALY
Last generation Hydraulic stabilizers with adjustable height of the cylinder with new locking system, standard on all models. Available with different length of the stabilizer cylinder. ...
-
Manufactured by Ensto Groupbased in FINLAND
The operating data exchange system (D.E.I.E.) is a control/monitoring unit that manages the remote control and monitoring of decentralised generating installations. Control cabinet for local spot generation, with measurements capacity for Wind mills, Photovoltaic generation, Micro generation, Gas turbine, ...
-
Manufactured by Van Halteren Technologiesbased in NETHERLANDS
knowledge when it comes to 3DOF motion platforms. The CEET motion platforms are designed to duplicate real aircraft behaviours. The hydraulic motion system can generate accelerations up to 1 G, and can be locked in any required crash position for emergency-slide operation training. ...
-
PremiumManufactured by Koller Maschinen- und Anlagenbau GmbHbased in GERMANY
The hydraulic vice have been designed for short-term clamping of downhole tools or other cylindrical workpieces. The 3-point clamping is carried out via a manual spindle and a hydraulically operated prism. The spindle is turned down to the diameter of the workpiece. Then the required clamping force is generated by the hydraulic ...
-
Manufactured by Raschig USA Inc.based in USA
is in the spray regime. Capacity improvements over conventional trays can be up to 20%.The RJ-MV valves are extruded from the tray deck and generally oriented parallel to the liquid flow. The unique crowned head of the valve promotes improved lateral vapor release which reduces froth height and entrainment and increases hydraulic capacity. Other ...
-
Manufactured by DynaQuip Controls Inc.based in USA
VME3 Series unibody economy ball valves are a great choice for lower pressure general hydraulic and petroleum shut-off needs. Valves are unibody bar stock construction with phosphate-coated bodies and NPT threaded connections in a reduced port design. Built strong and designed to last longer than lightweight imports. ...
-
Manufactured by DynaQuip Controls Inc.based in USA
VME1 Series 2-piece ball valves are a great choice for lower to medium pressure general hydraulic and petroleum shut-off needs. Valves are two-piece bar stock construction with corrosion-resistant phosphate coated bodies and NPT threaded connections in full and standard port design. Built strong and designed to last longer than lightweight imports. ...
-
Manufactured by GKN Sinter Metals Engineering GmbHbased in GERMANY
Common pump designs typically use a mix of different materials. Hence different thermal expansion factors create performance drops during the drive cycle of a vehicle. GKN´s G-Rotor pump overcomes this efficiency issue with a unique "ALL-PM-approach". Only PM steels are used and thus the uniform thermal expansion of components ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you