Refine by
Pipe Flare Equipment & Supplies
18 equipment items found
Manufactured by:Callidus Technologies - part of UOP, a Honeywell Company based inTulsa, OKLAHOMA (USA)
High stability flame retention system allows the flare to bum during all types of weather conditions. The pipe flare is the most basic type of flare tip. It is sometimes called an “utility flare”. Pipe flares will not smoke when burning low carbon content gases. The ...
Manufactured by:Callidus Technologies - part of UOP, a Honeywell Company based inTulsa, OKLAHOMA (USA)
The Demountable flare system provides flexible flaring operations to so that you can place multiple risers on a single support structure. They also allow you to perform maintenance to the tip at grade with minimal use of personnel at elevation. The demountable flare system features a derrick with the riser or risers mounted in such a way to permit lowering the flare tip to grade for service ...
Manufactured by:FlareTech Inc. based inStettler, ALBERTA (CANADA)
A utility flare stack is a fundamental type of open pipe flare used primarily for the combustion of waste gases. Its height is engineered to comply with safety regulations, ensuring proper dispersion of combustion products and minimizing ground level radiation, which is generally kept below 1500 BTU/hr/ft². The diameter is determined by the ...
Manufactured by:BD Environmental Solutions based inSeminole, FLORIDA (USA)
Utility Flares; Pipe Flares are unassisted equipment designed to combust hydrocarbons where non-smokeless operation is environmentally acceptable or where the waste gases produce little or no smoke due to their ...
Manufactured by:Smitsvonk Holland B.V. - a member of the Durag Group based inZoetermeer, NETHERLANDS
Ignition of waste gas from pipe flares, air and steam assisted flares and ground flares For most flare systems the pilot burner can not be accessed for service. Maintenance or replacement is not possible while the flare is in operation.To safeguard operation, Smitsvonk's pilots provide reliable ...
by:EnviroPro, Inc. based inHouston, TEXAS (USA)
Sometimes referred to as steam assisted pipe flares, upper steam flares have a steam manifold near the top of the flare tip. The manifold distributes steam to nozzles surrounding the outside diameter of the flare tip, just above the flare tip exit. Steam injected into the combustion zone pulls ...
Manufactured by:Europem N.V based inLier, BELGIUM
Utility Flares (Pipe Flares) are the most basic flare design available, to provide a robust, reliable and flexible solution for the flaring of large volumes of low pressure waste gas when smokeless operation is either not required or can be achieved without an assisting medium (like steam, air or gas). ...
Manufactured by:TRIC Tools, Inc. based inOakland, CALIFORNIA (USA)
The 1″ Copper Nut is used when attaching a new 1″ copper line to be pulled in behind the 1″ Water Line Bursting Heads (such as TT-WDGE-1WED). The Copper Flaring Tool (TT-WDGE-CFT) is used to flare the new copper pipe before it is attached to the head using the 1″ Copper Nut. Be sure to put the nut on the new ...
Manufactured by:Dinex A/S based inMiddelfart, DENMARK
Dinex designs and manufactures high quality clamps for connecting exhaust components. Our long-term experience enables us to provide custom designs tailored to suit your clamping requirements. We can offer high strength, low weight clamps for demanding applications such as those at elevated temperatures requiring gas-tight joints. Furthermore, we can give technical support in the form of product ...
Manufactured by:Hero Flare LLC based inKellyville, OKLAHOMA (USA)
Flame Front Generators are a traditional method of lighting flare pilots. An FFG panel mixes plant air and fuel gas into an ignition chamber. A spark plug ignites the mixture. The 'flame front' travels through a 1' pipe to flare ...
Manufactured by:Smitsvonk Holland B.V. - a member of the Durag Group based inZoetermeer, NETHERLANDS
Smitsvonk has decades of experience with direct electric ignition of flare units. A reproducible, high energy, highly reliable spark (described in the literature as 'plasma ignition') that is not susceptible to external influences such as moisture and dirt, guarantees the safe ignition and combustion of the residual gas in the flare. Such direct electric spark ignition may, for example, be used ...
Manufactured by:Aereon, part of Cimarron group based inLegnano (MI), ITALY
The dynamic (velocity) seal is a simple innovation which ensures significant cost savings over time. The reverse conical baffle design reduces flow area in the flare tip while simultaneously increasing purge gas velocity. In combination with the dynamic seal, a constant flow of purge gas will maintain a seal in flare system, ensuring that air infiltration does not occur. A vortex effect is ...
Manufactured by:FlareTech Inc. based inStettler, ALBERTA (CANADA)
The FlareTech Detonation Arrestor, model FT-DAX, is engineered to provide robust detonation safety within industrial piping systems. This passive safety device is essential for preventing flame propagation from sonic explosions or any ignition source toward sensitive equipment like tanks and vessels. Its placement at the inlet of a Flare Stack effectively stops ...
Manufactured by:LAMBDA Gesellschaft für Gastechnik mbH based inHerten, GERMANY
The LAMBDA biogas and sludge gas flare serves as an inspection and safety device at biogas and sludge gas plants for the thermal treatment of excess gas. Since the continuous process of gas production in these plants can only be influenced to a slight extent in the event of a failure of the utilisation plant, the LAMBDA flare safely disposes of the biogas not collected in the gas storage. This ...
Manufactured by:Europem N.V based inLier, BELGIUM
Since the 1980’s, key staff of Nutara have been responsible for the design, fabrication, installation, commissioning and maintenance of numerous flare systems including some of the most stringent and demanding applications. Nutara designs are optimized towards flexibility, robustness, low emissions, high thermal efficiency and ...
Manufactured by:Europem N.V based inLier, BELGIUM
Since the 1980’s, key staff of Europem have been responsible for the design, fabrication, installation, commissioning and maintenance of numerous flare systems including some of the most stringent and demanding applications.Europem’s extensive experience in flare design has resulted in a comprehensive range of elevated and ground flare systems and ancillaries to cover the needs of all ...
Manufactured by:Gasco Pty Ltd. based inMelbourne, AUSTRALIA
Flares, also known as gas flares and flare stacks, are a gas combustion device used in industrial plants such as petroleum refineries, chemical plants, and natural gas processing plants as well as at oil or gas production sites having oil wells, gas wells, offshore oil and gas rigs and landfills. Gasco, along with our technology partner, has supplied flares to the oil and gas, flares for ...
Manufactured by:Airoil Flaregas Pvt. Ltd. based inDist. Mehsana, INDIA
Optimization of an Elevated Staged Flare for a Large Refinery or a Gas Plant. In recent years most of the refineries, petrochemicals & gas processing plants are seen to be of larger capacities. Flare system for such plant are required to operate at two extreme flow conditions, one very high flow rates (in excess of 1000 tons per hour or the maximum design capacity rate) as well as at minimum ...