Waste-To-Energy Equipment In Pennsylvania
-
Manufactured by National Airoil Burner, Inc (NAO)based in USA
Oil, Gas, Vapor, Waste + Biogas / Bioliquids. Single or Combination ( dual, tri or quad ). Wide range of sizes and capacities. Low NOx , Ultra Low NOx, SD (Single Digit) NOx plus low CO. User friendly designs --- from Manual to Fully Automatic + Start Up & Training. Custom designs to meet your specific needs -- "YOUR WAY" -- even ROCKET TESTING. Computer controlled & video monitored (high ...
-
Distributed by Klaus Equipment Company (KEC)based in USA
RENTECH boilers are custom designed for each unique application. If your project requires a boiler, heat recovery steam generator, wasteheat boiler, fired packaged watertube boiler or other specialty boiler, you can depend on RENTECH to deliver a complete engineered ...
-
Distributed by Angstrom Sciences, Inc.based in USA
In Diode Sputtering, there is no use of magnets and thus, no magnetic field to contain the plasma. This means that plasma ions flow freely throughout the vacuum system and activate the entire surface area of the target, increasing target utilization. However, this also means that sputtered film particles are free to move throughout the chamber, not directly to the substrate. This can ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
AEREON's Cyclone Series Air-assisted flares are comprised of two risers (waste gas and air) and a blower system that provides supplemental combustion air. Air is fed by the blower into the air riser, to eventually combine with the process gas, which passes through its own secondary riser and is distributed at the flare tip through a proprietary AEREON Starfire burner tip. Upon mixing at the flare ...
-
Manufactured by Pennram Diversified Manufacturing Corporationbased in USA
A recent installation of 500 hp heat recovery boiler mounted to Pennram 2200 lb/hr incinerator at Egyptian cigarette ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Carbon dioxide is often used in fire extinguishers and snuffing systems with the intention of effectively extinguishing flames. When CO2 gas is a large percentage of a waste gas stream, at times it proves difficult to maintain a lit flare without the use of assist gas or a properly designed flame ring. Flare Industries’ industry-proven Flame Ring Flare Technology is recommended in low-BTU ...
-
Manufactured by Allegheny Technologies Incorporated (ATI)based in USA
ATI 22 alloy is a Ni-Cr-Mo alloy that provides outstanding resistance to pitting, crevice corrosion, intergranular attack, and stress corrosion cracking. The combination of Cr, Ni, Mo, and W provides excellent resistance to a broad range of both oxidizing and reducing ...
-
Manufactured by Kennametal Inc.based in USA
Plasma Transferred Arc (PTA) hardfacing is a versatile method of depositing high-quality metallurgically fused deposits on low cost surfaces. Soft alloys, medium and high hardness materials, and carbide composites can be deposited on a variety of substrates to achieve diverse properties such as mechanical strength, wear and corrosion resistance, and creep. PTA hardfacing has significant ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Triton sonic flare technology allows for safe, efficient and smokeless flaring at elevated oil and gas production rates by injecting sea water into the flame envelope. High pressure sea water injection reduces flare emissions, helps minimize overall radiation levels from the flame, abates combustion noise, and preserves flame characteristics during high wind events. The Triton sonic flare is ...
-
Manufactured by Therm-A-Cor Consulting, Inc.based in USA
The operation of combustion equipment must be undertaken with great care. Improper controls, poor supervision and faulty equipment have caused boilers, incinerators, oxidizers and process heaters to explode. Based on our experience with the design, fabrication, start up and operation of combustion equipment, Therm-A-Cor is qualified to prepare detailed forensic evaluations of equipment explosions ...
-
Manufactured by National Airoil Burner, Inc (NAO)based in USA
NAO flame arrestor burners used for NCG (non-condensable gases) in the pulp & paper industry. This unit shown is a forced draft FOUR stream waste burner -- including liquid turpentine and NCG ...
-
Manufactured by Advanced Plasma Solutions (APS)based in USA
Plasma Power Supply for Energy and Agricultural Applications: The Gliding Arc Plasma Research System can produce synthesis gas from gaseous (natural gas, propane, butane) and liquid (gasoline, diesel) fuels in partial oxidation and steam reforming modes of operation. It also can be used for CO2 sequestration and cleaning of gaseous products of biomass, coal, and municipal wastes ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Steam assisted flares are flares designed to dispose of heavier hydrocarbon gases which have a tendency to smoke. In order to prevent smoke formation, steam is injected into the waste stream using peripheral steam rings, center stream spargers and/or inner induction tubes. Steam flares are used in applications where high pressure steam is available on site. Steam flares are typically found in ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Air assisted flares are comprised of two risers (waste gas and air) and a blower system that provides supplemental combustion air. Air is fed by the blower into the air riser, to combine with the process gas, which passes through its own secondary riser. Upon mixing, the high-pressure air flow causes turbulence in the waste gas stream, improving mixing, and ultimately combustion efficiency. These ...
-
Manufactured by Alternate Heating Systemsbased in USA
Our Multi-Fuel boilers have the ability to heat homes and commercial spaces varying from 1,000 – 11,000sqft. They are ideal for those searching for a sturdy, long-lasting boiler with the ability to use a variety of fuels. For all the available ...
-
Manufactured by Clean Energy Heating Systemsbased in USA
Our self-contained air compressor kit will work with any of our waste oil furnaces or boilers. It’s an important part that helps your furnace work most efficiently and generate the maximum ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
The Certified Ultra-Low Emissions Burner (CEB) is an ultra-low emissions vapor device that utilizes premix surface combustion to effectively combust waste gases in a compact footprint. With VOC destruction efficiencies of up to 99.99% and a NOx emissions guarantee of ≤ 15 ppmv at 3% oxygen, carbon monoxide emissions guarantee of, smokeless operation and no luminous flame, the CEB is the best ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
The Model 100 Continuum Ignitor utilizes a high voltage electric arc to ignite a combustible air/gas mixture. This arc typically occurs every 20 seconds for a two second duration (timing is adjustable). The Continuum provides a spark inside a ‘slipstream’ chamber that diverts a portion of the waste gas to create a combustible air/gas mixture. This allows the Continuum ignitor to ...
-
Manufactured by SUEZ Water Technologies and Solutionsbased in USA
Designed to recycle biosolids into methane and valuable byproducts, SUEZ’s advanced anaerobic digestion technologies use bacteria in the absence of oxygen to break down matter to create biogas. The biogas can be combusted or oxidized and used for heating or with a CHP engine to produce electricity and heat; it can also be compressed and used as fuel for vehicles with the cake produced, used ...
-
Manufactured by Stainless Processing, Inc.based in USA
The plasma cutting process that is used to cut stainless steel (and other metals) of different thicknesses utilizes a plasma torch. An electrical arc is formed through an inert gas that is focused from a nozzle to the cutting surface. The arc turns the gas into a precise plasma beam that accurately cuts through steel. As with water jet cutting, this process is completely automated and driven by ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you