Wind Energy Equipment In Chile
-
Manufactured by Mainstream Renewable Powerbased in IRELAND
Mainstream has established a unique set of in-house renewable project execution capabilities which cover the development, engineering, procurement, financing, construction and operations phases – namely the entire wind project lifecycle. Mainstream's local teams have successfully obtained consent for 8.5 GW and delivered 1 GW of wind projects into commercial operation in Canada, Chile, ...
-
by Innergexbased in CANADA
Batteries are objects familiar to all, and utility-scale batteries used in energy storage systems are not much different from batteries we use in our every day lives, like in our cellphones or computers. Battery Energy Storage Systems charge and discharge energy at different times of the day, providing a service. Utility-scale batteries are stationary and connected to the grid, usually near a ...
-
Manufactured by Eshia S.L.based in SPAIN
Not including regulator controller. The AERO350W AERO400W are special marine environments. The AERO400W with 5 blades is the quietest ...
-
by Innergexbased in CANADA
Clean, renewable wind energy is an ideal alternative to fossil fuels. Wind turbines produce no atmospheric emissions, no harmful waste nor any other type of air or water pollution. And the noise produced by a wind turbine, as measured outdoors close to nearby homes, is no more than 40 dB, which is equivalent to the hum in a ...
-
Manufactured by Mainstream Renewable Powerbased in IRELAND
Mainstream is the most successful independent developer of offshore wind at scale globally. It has developed and consented Hornsea One and developed Hornsea Two totalling 2.6 GW in England and consented the Neart na Gaoithe offshore wind project in Scotland, 450 MW. These projects represent 22% of the UK’s offshore wind capacity either in operation or under ...
-
Manufactured by Elecnorbased in SPAIN
In wind energy, Elecnor has not only built numerous turnkey wind farms throughout Spain for various developers, but also acts as a developer and operator through its subsidiary ...
-
Manufactured by Elecnorbased in SPAIN
Feasibility studies. Cost-finance analysis. Project administration procedures. Permitting and planning management. Construction and detailed engineering project design. Turnkey construction. Operation and maintenance. Operations ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
Lattice and tubular towers of up to 30 meters height are available for ANTARIS small wind turbines.. All the masts have approved structural calculations and are delivered with foundation plans. In addition, the lattice masts provide the possibility of having a surface for advertising ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
The feed-in converter smart!wind was designed by SPE especially for small wind turbines (SWT) with a power range from 5.5 to 20 kW. Besides the control functions for a SWT the smart!wind provides several protective functions supporting a safe operation of your SWT. Small hydro plants as well as CHP’s offer additional possible applications. Our feed-in converter is available in the following ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
Working grid feed in at 2.5 m/sec. wind speed after start up, depending on the repeller. Purpose built for inland areas with low untill moderate wind speed. From an average wind speed with 7.0 m/sec. we use a repeller with 5.8 m ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
Permanent-magnet rotor, brushless, gearless, maintenance-free. Extremely strong permanent magnets for a high level of efficiency. (NdFeBo permanent magnets, resistent to temperatures up to 150° C). Special ball bearings for reliably taking up radial and axial forces. 3-phase current. Separate rectifier. Either direction of rotation. Voltage 0-1000 VDC. Start of feed-in at approx. 100 rpm. ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
Permanent-magnet rotor, brushless, gearless, maintenance-free. Extremely strong permanent magnets for a high level of efficiency. (NdFeBo permanent magnets, resistent to temperatures up to 150° C). 3-phase current. Separate rectifier. Either direction of rotation. Voltage 0-400 V. Start of feed-in at approx. 145 rpm. Power: 2.700 watts at 380 rpm and 330 V. Evenly rising power curve. Weight: ...
-
Manufactured by DEWESoftbased in SLOVENIA
The Dewesoft solution can measure all the power quality parameters according to IEC 61000-4-30 Class A. In comparison to other power quality analyzers it’s possible to do more detailed analysis (e.g. raw data storing, behavior at faults, calculation of additional parameters ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Pit Flares are generally selected and designed in order to combust a mixture of vapor and liquid from a single source. While most often designed to operate non-smokelessly, through use of Flare Industries’ various Pit Flare technologies, smokeless operation can often be achieved. The flare pit (or “Burn Pit”) is usually constructed of an excavation, lined with a non-combustible ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
Working grid feed in at 2.5 m/sec wind speed after start up, depending on the repeller. Purpose built for inland areas with low untill moderate wind speed. From an average wind speed with 7.5 m/sec. we use a repeller with 4.0 m ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
NdFeBo permanent magnets – these are the strongest permanent magnets currently available. No cogging torque, maintenance-free!. To ensure long, maintenance-free service of the generators in the ANTARIS wind turbine, the copper winding in the stator is configured to meet insulation class H (180° C). As the repeller is attached directly on the generator shaft, BRAUN Windturbines GmbH ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
The PVI-3.0/3.6/4.2-TL-W wind turbine inverter is designed with ABB’s proven high performance technology. This dual stage transformerless wind inverter offers a unique combination of high efficiency, installer-friendly design and very wide input voltage range ensuring high energy harvesting. The high speed and precise power curve tracking algorithm allows to best match the power curve of ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
The rotor blades have a computer-designed, aerodynamic profile and are manufactured by the hand lay-up method. The mix of glass fibre-carbon fibre laminate guarantees the highest quality standard at a reasonable price. A special tape is fixed to the leading edge to guarantee optimum edge protection. By using the same moulds for each different diameter, the blades are reproduced identically and ...
-
Manufactured by BRAUN Windturbinen GmbHbased in GERMANY
Permanent-magnet rotor, brushless, gearless, maintenance-free. Extremely strong permanent magnets for a high level of efficiency. (NdFeBo permanent magnets, resistent to temperatures up to 150° C). Special ball bearings for reliably taking up radial and axial forces. 3-phase current. Separate rectifier. Either direction of rotation. Voltage 0-1000 VDC. Start of feed-in at approx. 100 rpm. ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you