Cyber Power - Model PDU20MHVIEC8FNET - Monitored PDU Datasheet

PowerDistributionUnitUser Manualwww.CPSww.comK01-0000181-00Table of Contents Model List...............................................................1Introduction............................................................1Package Contents.................................................................. 1For 1U Series............................................................1For 2U Series............................................................2Safety Precautions.............................................................. ...2Product Features................................................................... . 31U 15A Series...........................................................3Technical Specification........................................31U 20A Series...........................................................4Technical Specification........................................42U Series..................................................................5Technical Specification........................................5 Installation Guide...................................................6Horizontal Installation ...........................................................6For 1U Model............................................................6For 2U Model............................................................7Vertical Installation (1U Model Only)...................................9For 1U Model............................................................9Electrical Installation.............................................................9Network Installation.............................................................10Operation..............................................................11Metered Readout..................................................................11Basic Operation.......................................................11PDU Status Screen.................................................11Current Level.....................................................11Input Voltage.................................................. ....11Power................................................................11IP Address.........................................................11Outlet Control.....................................................11Remote Management...........................................................11LED Indicators.....................................................................12Device Reset........................................................................12Unattended/Automatic Shutdown......................................12Firmware Upgrade...............................................12Troubleshooting...................................................13Frequently Ask Questions (FAQ)........................13Conformance Approvals.....................................13Customer Service & Warranty............................14Product Registration..............................................................14CyberPower International.......................................................14Limited Warranty ..................................................................14Appendix A-Hyper Terminal................................15Appendix B-Power Device Network Utility........16Overview......................................................................... ......16Installation...................................................................... ....... 16Launch Program............................................................ ........17Getting Started............................................................... ........17Advanced Settings......................................................... .........18 Model List 1U Switched Series PDU15SW8FNET PDU15SWHVIEC8FNET PDU20SW8FNET PDU20SWT8FNET PDU20SWHVIEC8FNET 1U Monitored Series PDU15M8FNET PDU15MHVIEC8FNET PDU20M8FNET PDU20MT8FNET PDU20MHVIEC8FNET????????????????PDUMounting Bracket: 2 short & 2 longCord Retention TrayCable Ties / Qty. 106 (M3x6) Cord Retention Tray Mounting Screws (Includes two spares)6 (M5x12) Screws / 6 Washers (Includes two spares for each)RJ45/DB9 Serial Port Connection CableRJ45/DB9 Serial Port Connection CablePower Cord 10 feet, IEC-320 C13/ IEC-320 C14 (PDU15SWHVIEC8FNET/PDU15MHVIEC8FNET Model Only)Power Cord 10 feet, IEC-320 C19/ IEC-320 C20 (PDU20SWHVIEC8FNET/PDU20MHVIEC8FNET Model Only)IntroductionPackage Contents (For 1U Series)2U Switched Series PDU30SWT16FNET PDU30SWHVT16FNET2U Monitored Series PDU30MT16FNET PDU30MHVT16FNET User Manual Registration Card CDCyberPowerReliability. Quality. Value.RUser's ManualDocumentationCable Ties / Qty. 2010 (M3x6) Cord Retention Tray Mounting Screws (Includes two spares)6 (M5x12) Screws / 6 Washers (Includes two spares for each)10 (Flat Head M4x5) Bracket Mounting Screws (Includes two spares)10 (Flat Head M4x5) Bracket Mounting Screws (Includes two spares)PDUMounting Brackets x 2????????????????User Manual Registration Card CDCord Retention Trays x 2DocumentationBefore using, please check to ensure the package contains all the items shown above. If there are missing parts, please contact CyberPower technical support at www.CPSww.com or call 1-952-403-9500 when you are US customers. For Europe customers, please contact CyberPower at www.eu.cyberpowersystems.com/contact.htm or call +31 (0)40-2348170.Safety PrecautionsRead the following before installing or operating the Power Distribution Units (PDU):Use only the supplied hardware to attach the mounting brackets.The PDU must be plugged into a three-wire, grounded outlet on a circuit that is protected by a fuse or circuit breaker. For PDU15xxxxx series, pleaseuse 15A circuit protector. For PDU20xxxxx series, please use 20A circuit protector. For PDU30xxxxx series, please use 30A circuit protector.Connection to any other type of power outlet may result in a shock hazard.Do not use extension cords or adapters with this PDU.Never install a PDU, or associated wiring or equipment, during a lightning storm.Ensure the power cord, plug, and socket are in good condition.CAUTIONTo prevent the risk of fire or electric shock, this PDU should be installed in a temperature and humidity controlled indoor area free of conductive contaminants. Do not install this PDU where excessive moisture or heat is present.IntroductionPackage Contents (For 2U Series) CyberPowerReliability. Quality. Value.RUser's Manual3 4Front panel descriptionNEMA Type1 2 3 4 5 6 7 8SelectKWVoltsAmps- Normal- Warning- OverloadTx/RxLinkSerial PortResetYU0-0000026-00PDU20SWHVIEC8FNETA. Power CordB. AC Output OutletsC. Current LevelD. Input VoltageE. PowerF. Load IndicatorG. Ethernet PortH. Tx/Rx IndicatorI. Link IndicatorJ. Outlet Indicator (switched series only)K. Serial Port (RJ45 modular port)L. Select ButtonM. PDU Status ScreenN. Reset ButtonRear panel descriptionTechnical Speci?cationProduct Features (1U 15A Series)IEC Type1 2 3 4 5 6 7 8SelectKWVoltsAmps- Normal- Warning- OverloadTx/RxLinkSerial PortReset PDU15SWHVIEC8FNETA N M L KADDE CFF G H IBJAAN M L KE C G H IBA. External Site GroundJProduct Features (1U 20A Series)Front panel descriptionNEMA TypeA. Power CordB. AC Output OutletsC. Current LevelD. Input VoltageE. PowerF. Load IndicatorG. Ethernet PortH. Tx/Rx IndicatorI. Link IndicatorJ. Outlet Indicator (switched series only) K. Serial Port (RJ45 modular port)L. Select ButtonM. PDU Status ScreenN. Reset ButtonRear panel descriptionTechnical Speci?cationIEC TypeA N M L KDE C F G H IBJD FA N M L KE C G H IBJ1 2 3 4 5 6 7 8SelectKWVoltsAmps- Normal- Warning- OverloadTx/RxLinkSerial PortReset PDU20SWHVIEC8FNET1 2 3 4 5 6 7 8SelectKWVoltsAmps- Normal- Warning- OverloadTx/RxLinkSerial PortReset PDU20SWT8FNETA. External Site GroundAAModel Name PDU15SW8FNET PDU15SWHVIEC8FNET PDU15M8FNET PDU15MHVIEC8FNETInput Nominal Voltage 100-120V 200-240V 100-120V 200-240V Frequency Derated Input Current12A 12A(UL)/10A(CE) 12A 12A(UL)/10A(CE) Plug Type NEMA 5-15P IEC-320 C14 NEMA 5-15P IEC-320 C14 Power Cord Type SR (14 AWG) Socket SR (14 AWG) Socket Power Cord Length12 ft/3.65 m 10 ft/3.05 m 12 ft/3.65 m 10 ft/3.05 mOutput Nominal Voltage 100-120V 200-240V 100-120V 200-240V Derated Output Current12A 12A(UL)/10A(CE) 12A 12A(UL)/10A(CE) Outlet Type NEMA 5-15R IEC-320 C13 NEMA 5-15R IEC-320 C13 Outlet NumberNetworking Protocol Support ConnectivityPhysical Dimension (H x W x D)Environmental Humidity Altitude TemperatureSafety Approvals CertificationsUL 60950,FCC Class A UL 60950, CE,FCC Class AUL 60950,FCC Class A UL 60950, CE,FCC Class AWarranty Product Warranty 3 years repair or replaceRJ451.73" x 17.05" x 4.41"/44mm x 433mm x 112mmTCP/IP, UDP, DHCP, SNMP, HTTP0 to 95% Non-condensing14700 ft/4500 m32? to 104?/0? to 40?Switched Series (1U 15A) Monitored Series (1U 15A)850/60HzTENF8M02UDPTENF8WS02UDPTENF8TM02UDPTENF8TWS02UDPInput Nominal Voltage 100-120V 200-240V 100-120V 200-240V Frequency Derated Input CurrentP02-5 AMENP02-5 AMENP02-5L AMENP02-5L AMEN Power Cord Type SR (12AWG) Socket SR (12 AWG) Socket Power Cord Length12 ft/3.65 m 10 ft/3.05 m 12 ft/3.65 m 10 ft/3.05 mOutput Nominal Voltage 100-120V 200-240V 100-120V 200-240V Outlet Type NEMA 5-20R IEC-320 C13 NEMA 5-20R IEC-320 C13 Outlet NumberNetworking Protocol Support ConnectivityPhysical Dimension (H x W x D)Environmental Humidity Altitude TemperatureSafety Approvals CertificationsUL 60950,FCC Class A UL 60950, CE,FCC Class AUL 60950,FCC Class A UL 60950, CE,FCC Class AWarranty Product Warranty 3 years repair or replace1.73" x 17.05" x 4.41"/44mm x 433mm x 112mm02C 023-CEI02C 023-CEI8TCP/IP, UDP, DHCP, SNMP, HTTP0 to 95% Non-condensing14700 ft/4500 m32? to 104?/0? to 40?RJ45Switched Series (1U 20A) Monitored Series (1U 20A) Plug Type Derated Output Current16A16AModel Name50/60HzPDU20SWHVIEC8FNET PDU20MHVIEC8FNET5 6Installation GuideProduct Features (2U Series)Front panel descriptionNEMA TypeBank 1 , 20ABank 2 , 20A21 3 4 5 6 7 8161514131211109Tx/RxLinkSerialPortAmpsVoltsKW- Warning- OverloadB1 B2 - NormalSelectYU0-0000028-00ResetA. Power CordB. AC Output OutletsC. Input Circuit BreakerD. Current LevelE. Input VoltageF. PowerG. Load IndicatorH. Ethernet PortI. Tx/Rx IndicatorJ. Link IndicatorK. Outlet Indicator (switched series only)L. Serial Port (RJ45 modular port)M. Select ButtonN. PDU Status ScreenO. Reset ButtonRear panel descriptionIEC TypeTechnical Speci?cationCAUTION Please use only the provided screws through the entire installation process.Horizontal InstallationFor 1U ModelStep 1. Mounting Bracket Installation Use the provided Mounting Bracket Screws (8) to attach the SHORT Mounting Brackets (2) to the PDU.If you plan on attaching the Cord Retention Tray to the PDU, you will need to use the LONG Mounting Brackets (2).Step 2. PDU Mounting Use the supplied Washers (4) and Screws (4) to secure the PDU to your existing rack system.Bank 1 , 15ABank 2 , 15A200-240VAC50/60 Hz24A MAX12A MAX PER OUTLET21 3 4 5 6 7 8161514131211109Tx/RxLinkSerialPortAmpsVoltsKW- Warning- OverloadB1 B2 - NormalSelectYU0-0000028-00ResetA O N M LD F EC HBKGA O N M LD F EC HBKGA. External Site GroundAAIJIJ100-120VAC50/60 Hz24A MAXModel Name PDU30SWT16FNET PDU30SWHVT16FNET PDU30MT16FNET PDU30MHVT16FNETInput Nominal Voltage 100-120V 200-240V 100-120V 200-240V Frequency Derated Input Current Plug Type NEMA L5-30P NEMA L6-30P NEMA L5-30P NEMA L6-30P Power Cord Type Power Cord LengthOutput Nominal Voltage 100-120V 200-240V 100-120V 200-240V Derated Output Current Bank Number Outlet Type NEMA 5-20R IEC-320 C13 NEMA 5-20RIEC-320 C13*12/IEC-320 C19*4 Outlet NumberCircuit BreakNetworking Protocol Support ConnectivityPhysical Dimension (H x W x D)Environmental Humidity Altitude TemperatureSafety Approvals CertificationsWarranty Product Warranty 3 years repair or replaceUL 60950, FCC Class A3.46" x 17.05" x 4.41"/88mm x 433mm x 112mm2RJ4516YesTCP/IP, UDP, DHCP, SNMP, HTTP0 to 95% Non-condensing14700 ft/4500 m32? to 104?/0? to 40?SR (10 AWG) Output Current (each bank))U2( seireS derotinoM)U2( seireS dehctiwS50/60Hz24A10 ft/3.05 m 12 ft/3.65 m15A 20A 15A20A24A7 8Installation GuideInstallation GuideStep 3. Cord Retention Tray Installation (optional) Attach the Cord Retention Tray to the PDU with the 4 supplied Cord Retention Tray Mounting Screws.Use the provided Cable Ties to fasten each cord to the Cord Retention Tray. Use the provided Cable Ties to fasten each cord to the Cord Retention Tray. Step 3. Cord Retention Tray Installation (optional) Attach the Cord Retention Tray to the PDU with the 8 supplied Cord Retention Tray Mounting Screws.For 2U ModelStep 1. Mounting Bracket Installation Use the provided Mounting Bracket Screws (8) to attach the Mounting Brackets (2) to the PDU.Step 2. PDU Mounting Use the supplied Washers (4) and Screws (4) to secure the PDU to your existing rack system.CAUTIONThe PDU must be plugged into a three-wire, grounded wall receptacle only. The wall receptacle must also be connected to an appropriate branch circuit/main with fuse or circuit breaker protection. Connection to any other type of wall receptacle may result in a shock hazard.9 10Installation GuideInstallation GuideStep 3 – Attach equipment It is extremely important not to exceed the PDUs maximum current load (as outlined in the Specifications section). In order to determine your total load, simply use the Metered Readout on the front of the PDU.Electrical InstallationStep 1 –Receptacle evaluation Ensure that the plug type of your PDU unit matches the wall receptacle type that you are using.Step 2 – Plug the PDU into the wall receptacleStep 1 – Attach the LAN Cable Using a CAT5 RJ45 cable, attach one end to the Ethernet port on the front of the PDU, and the other end to a network port.Step 2 – Establish the PDU IP address Assigning an IP address to the CyberPower PDU requires the user to have an available IP address that is valid on the respective network. If an available IP address is unknown, contact the network administrator to obtain one.The default IP is 192.168.20.177 and the default DHCP function is on.There are multiple methods for setting up the IP address on the PDU. Please follow the instructions below for the method that is appropriate for your application.Please make sure the PDU is powered on during this process.Option 1 (recommended): Power Device Network Utility1. Use the included CD “PDU Software Installation CD” to install the Power Device Network Utility program.2. Open the Power Device Network Utility software (Start => Power Device Network Utility).3. Highlight the PDU device from the list and select Edit and Setup device => Assisted Setup from the menu.4. Configure the IP Address, Subnet Mask, and Gateway Address to match your network settings.5. Enter the user name and password of the PDU device at the Authentication menu. The default username is “cyber” and the default password is “cyber”.For further information and installation instructions, see Appendix B.Option 2: DHCP Server1. Ask your administrator if there is DHCP server on the LAN.2. Make sure the DHCP is Enabled.3. Make sure the network connection is ready and power on the PDU.4. The PDU will obtain an IP address from the DHCP server automatically.Option 3: Address Resolution Protocol (ARP) Command1. Obtain the MAC address from the sticker on the PDU.2. At a command prompt, type the following: “arp-s [available IP address] [MAC address of PDU]”. Example: arp -s 192.168.20.240 00-0c-15-80-00-01 IP Address MAC Address3. Use the Ping command to assign a size of 123 bytes to the IP.* Type in “ping 192.168.20.240 -l 123” then press Enter* If the replies are received, your computer can communicate with the IP addressOption 4: Hyper TerminalIn order for Hyper Terminal to interface with the PDU, the PC/ server must be connected directly to the PDU via the serial port.1. Use the included RJ45/DB9 serial port connection cable, attach one end to the serial port on the front of the PDU, and the other end to the PC/ server.2. Open the Hyper Terminal software on your PC and select a name and icon for the connection.3. Setup the COM port settings using the following values* Bits per second: 9600* Data bits: 8* Parity: None* Stop bits: 1* Flow control: NoneNetwork InstallationStep 2. PDU Mounting Use the supplied Washers (2) and Screws (2) to secure the PDU to your existing rack system.Vertical Installation (1U Model Only)For 1U ModelStep 1. Mounting Bracket Installation Use the provided Mounting Bracket Screws (8) to attach the SHORT Mounting Brackets (2) to the PDU.11 12OperationOperationInstallation Guide4. Type “setup” and press Enter to enter the Authentication menu.5. Enter the user name and password of the PDU device at the Authentication menu. Note: The default username is “cyber” and the default password is “cyber”. For further information and configuration via Hyper Terminal, see Appendix A- Hyper Terminal.Metered ReadoutTx/RxLinkSerialPortAmpsVoltsKW- Warning- OverloadB1 B2 - NormalSelectYU0-0000028-00ResetThe Metered Readout provides instant status updates of the PDU’s Voltage, Current, Power conditions as well as the local IP address of the unit to the user. In addition, it also allows the user to control each outlet of the PDU.Basic Operation Screen Selection- To toggle the different status screens, press the Select button next to the PDU status screen.Pressing the Select once will toggle to the next status screen.Pressing and holding the Select button for 3 seconds will display the local IP address of the unit.Pressing and holding the Select button for 6 seconds will enter the outletcontrol mode.PDU Status Screen Current LevelAmpsVoltsKWThe Current Level screen shows the total current draw of the connected equipment. Units are listed in Amps.The Power screen shows the total power that the devices connected to the PDU consumes. Units are listed in kilowatts.The IP Address screen displays the local IP address of the PDU unit. Note: If the PDU is not connected to a LAN, the readout will display the default IP address.The Outlet screen shows the condition of each outlet in sequence. When the outlet is on, the light below this outlet is on and an upper square appears next to the number of the outlet. To switch the outlet to off mode, press the Select button once and the upper square will change into lower square. At this time, please wait for 1 second and the outlet will turn to off mode automatically.The Input Voltage screen measures the AC voltage that the system is receiving from the utility wall receptacle. This can be used as a diagnostic tool to identify poor-quality input power. Units are listed in Volts.Input VoltagePowerOutlet Control (switched series only)AmpsVoltsKWAmpsVoltsKWAmpsVoltsKWAmpsVoltsKWAmpsVoltsKWRemote ManagementThe remote management function of the CyberPower PDU provides for monitoring the PDU vitals, controlling outlets, and utilizing SNMP functionality. Remote management is performed via the web interface. To access the web interface, please follow the instructions below:1. Enter the IP address of the PDU into a web browser (Internet Explorer, Firefox).2. Enter the user name and password of the PDU device at the authentication screen. Note: The default username is ”cyber” and the default password is “cyber”.After entering Web interface for the first time, please set the correct time in [System=>General=>Date & Time]For additional information about the features and functionality of CyberPower Management Console, please refer to the PDU Software Installation CD.LED IndicatorsDevice ResetTo reset all the settings to default except for the IP address, press and hold the Reset Button for 3 seconds. To reset all the settings to default, press and hold the Reset Button for 6 seconds. Unattended/Automatic ShutdownPowerPanel Business Edition software automatically saves open files and gracefully shuts down the operating system in an intelligent and orderly fashion. PowerPanel must be installed on every PC for which the shut down is to take place. The PC receives SNMP messages directly from the PDU, and these messages can be scheduled for an exact date/time, or can be performed immediately. Follow the directions below for setting up Unattended/Automatic Shutdown.Step 1. PC Configuration1. Install PowerPanel Business Edition Client on every PC that will be part of the shut down process. (Follow the instructions in the PowerPanel Business Edition Client user manual).2. Configure the settings in PowerPanel Business Edition Client. See the PowerPanel Business Edition Client User Manual for additional help.Step 2. PDU Configuration1. Verify that the IP address of all PCs that will be part of the shut down process are included in the Client List of web interface (For additional information, please refer to the user’s manual in the PDU Software Installation CD).Step 3. NotificationNotifying the PCs of potential outlet shutdown can be accomplished using the following methods:Outlets Control Menu: Performing the task of turning off or rebooting outlets.Scheduling Menu: Setting the scheduler to perform the task of turning off or rebooting outlets. The notification will occur prior to the scheduled date/time.Outlet Overload: In event of a PDU overload, notification will be sent prior to thePDU shutting down.Firmware UpgradeBy upgrading the Firmware, you can obtain new features and updates/improvements to existing functionality. There are two files to update in order to upgrade the firmware version: * cpspduafw_XXX.bin * cpspduadata_XXX.binUse the following steps to upgrade the firmware. 1. Download the latest firmware from cyberpowersystems.com 2. Extract the file to “C:\\\\”3. Open a command prompt window4. Login to the PDU with FTP command, type * ftp * ftp> open * To [current ip of the PDU] [port] ; EX: To 192.168.22.126 21 * Input USER NAME and PASSWORD (same as the administrator account in Web interface default : cyber ; cyber)IP AddresssutatSrotacidnI DescriptionGreen The total PDU power load is normal.Orange Near overload.Red Overload..ffo si rewop UDP ehTffOOn(Green) The PDU power is on.Receiving/transmitting data packet.Reset finished..NAL eht ot detcennoc si UDP eht setacidnInOOffIndicates the PDU is not connected to theLAN..rewop gnidivorp dna no si teltuo ehTnO.ffo si teltuo ehTffOOutletLoadTx/RxFlashLINK13 14Firmware Upgrade Customer Service & WarrantyTroubleshootingFrequently Ask Questions (FAQ)5. Upgrade the cpspduafw_XXX.bin, type * ftp > bin * ftp > put cpspduafw_XXX.bin6. Upgrade complete, type * ftp > quit7. The system will reboot after you type “quit” 8. Login to the FTP again * ftp * ftp> open * To [current ip of the PDU] [port] ; EX: To 192.168.22.126 21 * Input USER NAME and PASSWORD 9. Input USER NAME and PASSWORD Upgrade cpspduadata_XXX.bin * ftp > bin * ftp > put cpspduadata _XXX.bin10. Upgrade complete , type * ftp > quit11. The system will reboot after you type “quit” You can check to see if the firmware upgrade was successful by checking the”Firmware version” on the [System->About] webpage.Note: Please do not turn the PDU off when processing the Firmware upgrade.Q. What do I do if I’ve lost the Administrator username and/or password?A. Resetting the PDU will set the username and password back to system default. Please see the Device Reset section to reset the PDU.Conformance ApprovalsFCC WarningWARNING This equipment has been tested and found to comply with the limits for a Class A Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.Any special accessories needed for compliance must be specified in the instruction.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Notice: (1) An unshielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord by used. (2) Use only shielded cables to connect I/O devices to this equipment. Note: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS WQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.The Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation.Cet appareil numerique de la class A respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.Product RegistrationThank you for purchasing a CyberPower product. Prompt product registration entitles coverage under the Limited Warranty, and also allows the opportunity to be notified of product enhancements, upgrades, and other announcements.Registration is quick and easy at www.cyberpowersystems.com/support/warranty-registration.htmlCyberPower InternationalFeel free to contact our Tech Support department with installation, troubleshooting, or general product questions.CyberPower North AmericaPhone: +1-952-403-9500Email: sales@cyberpowersystems.comWeb: www.cyberpowersystems.comMail: 4241 12th Avenue E., Suite 400 Shakopee, MN 55379Hours of Operation: Monday-Friday 8:00 AM-5:00 PM (CST)CyberPower EuropeEmail: sales@cyberpower-eu.comWeb: www.eu.cyberpowersystems.comLimited WarrantyRead the following terms and conditions carefully before using the CyberPower PDU series. By using the Product, you consent to be bound by and become a party to the terms and conditions of this Limited Warranty. If you do not agree to the terms and conditions of this Warranty, you should return the Product for a full refund prior to using it.Who Is Providing This Warranty?CyberPower Systems (USA), Inc. /CyberPower Systems B.V. /Cyber Power Systems France ("CyberPower") provides this Limited Warranty. What Does This Warranty Cover?This warranty covers defects in materials and workmanship in the Product under normal use and conditions.What is the Period of Coverage?CyberPower provides a 3-Year warranty to the original purchaser who owns the Product.Who Is Covered?This warranty only covers the original purchaser.Coverage ends if you sell or otherwise transfer the Product.How Do You Get Service?1. You can use the contact information mentioned above for instructions.2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and Request a Claim Number.3. You must provide a purchase receipt (or other proof of the original purchase) and provide a description of the defect. What Will We Do To Correct Problems?CyberPower will inspect and examine the Product. If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you paid for the Product (purchase receipt showing price paid is required).If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the connected equipment. We will repair or replace the equipment that was damaged because of the failure of our Product or pay you the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the damage. We will use Orion Blue Book, or another a third-party valuation guide, or eBay, craigslist, or other source to establish that amount. Our liability is limited to the amount, if any, stated in the Technical Specifica-tions.noituloSesuaC elbissoPmelborP1. Breaker tripped2. Loose power cordAmperagedisplayed onMetered Readoutexceeds the unitscapability1. OverloadThe load indicator shows red when overload.Reduce the load on the PDU until the overloadis gone. If the problem remains, contacttechnical support..rekaerB teseRdaolrevo deniatsuS .12. Excessive ambient or internal temperaturesIf the problem remains, contact technicalsupport.3. Faulty breakerPDU outlets do notprovide power toconnectedequipmentReset Breaker, check if plug is completelyconnected. If the problem remains, contacttech support.Circuit breakershave tripped15 16Customer Service & WarrantyAppendix A-Hyper TerminalWho pays for shipping?We pay when we send items to you; you pay when you send items to us. What Are Some Things This Warranty Does Not Cover?1. This Warranty does not cover any software that is damaged or needs to be replaced due to the failure of the Product or any data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of software.2. This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or maintenance, or use with items not designed or intended for use with the Product, such as laser printers, appliances, aquariums, medical or life support devices, etc.What are the Limitations?1. This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired and grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use of any adapters or other connectors.2. The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly connected to the Product and not "daisy-chained" together in serial fashion with any extension cords, another Product or device similar to the Product, surge suppressor, or power tap. Any such installation voids the Limited Warranty.3. The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with any license, instruction manual, or warnings provided with the Product and the equipment connected to it.4. The Product must have been used at all times within the limitations on the Product's VA capacity.5. The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.Appendix B-Power Device Network UtilityOverviewThe CyberPower Power Device Network Utility is an easy-to-use interface which is used for establishing IP addresses on CyberPower PDU devices. InstallationStep 1. Insert the CD labeled “PDU Software Installation CD” into the CD/DVD drive.Step 2. Select Power Device Network Utility from the installation menu (Shown in Figure 1.). Figure 1. Installation MenuStep 3. Select Next in the software wizard.Step 4. Choose an installation directory and user settings. Select Next (Shown in Figure 2.).Hyper Terminal software can be used for basic PDU configuration. It utilizes a text-based interface and menu system. Navigation through the interface is done by typing the number of the menu option and pressing the Enter key. Note: The session will timeout and logout after 3 minutes of inactivity. Menu options are shown below:[Power Manager Configuration Main Menu]1. Network Settings2. System Configuration3. Account Settings4. Configure System to Defaulte. Exit[Network Group Configuration Utility Menu]Ethernet Address: 00-0C-15-03-04-351. System IP: 192.168.20.952. Subnet Mask: 255.255.255.03. Default Gateway: 192.168.20.14. Web/Http Port: 805. BOOTP (DHCP): Enable0. Return to previous menu[System Group Configuration Utility Menu]1. Internal Date (mm/dd/yyyy) : 04/15/20092. Internal Time (hh:mm:ss): 06:04:253. System Name: Power Manager4. System Contact: Administrator5. System Location: Server Room[Account Group Configuration Utility Menu]1. Web Administrator User Name: cyber2. Web Administrator User Password: cyber3. Web Device User Name: device4. Web Device User Password: cyber5. COM Port Configuration Password: cyber0. Return to previous menu[Default Group Configuration Utility Menu]1. Reset System to Default2. Reset System to Default Except IP0. Return to previous menu Figure 2. Installation folder and settingsStep 5. Select Next to comfirm the settings and install.Step 6. Select Close to finalize the installation.17 18Appendix B-Power Device Network Utility Appendix B-Power Device Network UtilityPressing Stop will cancel the scan/refresh process.Note: If your computer has a software firewall installed, you may see a Windows Security Alert message (Shown in Figure 5.).In Windows XP SP2, the default firewall alert message is shown as Figure 5. You need to allow the Power Device Network Utility access through the firewall.Step 2. Assign a valid IP Address to the PDUOption 1: Assisted Setup (recommended)With the appropriate device selected from the Equipment List, open the Network Settings menu (Shown in Figure 6.). [Tools=>Device Setup]. In the Device Network Setting Menu, enter a valid IP address, subnet mask, and gateway address to setup the PDU device. Figure 6. Network Setting Menu (Device Setup)Note: The DHCP option is not available for all power devices.Step 3. AuthenticationEnter the user name and password of the PDU device at the Authentication menu (Shown in Figure 7.). Note: The default username is “cyber” and the default password is “cyber”.Figure 7. Authentication screen Figure 3. Power Device Network UtilityGetting StartedThe Power Device Network Utility scans the network for devices with MAC addresses that match CyberPower network hardware. Once found, the device(s) can then be figured with a specific IP address, subnet mask, and gateway address. This allows the device(s) to function properly on the network and interface with CyberPower Management Console.Step 1. Select the appropriate PDU device from the Equipment List (Shown in Figure 4.). Figure 4. Equipment ListNote: If the PDU does not appear on the list, click the Refresh button to rescan the network. If it still does not appear, ensure that the PDU is turned on and was installed correctly. Launch ProgramTo launch the Power Device Network Utility and get started, select Programs from the Start menu in Windows and locate the new folder and icons for Power Device Network Utility. Select Power Device Network Utility from the program folder (Shown in Figure 3.).Figure 5. Windows Security AlertAdvanced SettingsTimeout SettingsThe Timeout Setting (Shown in Figure 8.). [Edit=>Timeout Settings] is used to specify the wait time when scanning for network PDU devices. When there are many devices on the local network, it may take extended periods of time to locate all the devices. The timeout function is used to limit the search time. The default setting is 3 seconds. Valid values are 3 to 60 seconds.Figure 8. Timeout Setting ?? MU A B C D E F G H I