Model NG 24 TP1 SAW - Photovoltaic Module Brochure

Naps Pallas 200-210G SAW• Carefully selected polycrystalline silicon solar cells for close tolerance• Solar cells treated for reduced reflection and for efficient conversion of both direct and diffuse light• Electrical circuit laminated between layers of ethylene vinyl acetate (EVA) for electrical isolation, moisture resistance and UV stability• Low iron content, tempered glass for mechanical protection and high light transmission• Multi-layered polymer backsheet for resistance to abrasion, tears and punctures and dependable electrical insulation• Rugged and lightweight anodised aluminium frame with mounting, grounding and drainage holes• Junction box with pre-fitted cables and quick connectors designed for ease and safety• Wired-in bypass diodes to reduce potential loss of power and damage from partial array shading• Tested for a wide range of operating conditions (-40°C to +85°C)• Tested to withstand the highest wind, hail storm and snow load requirements (5400 N/m2)• Designed to meet or exceed the environmental requirements of IEC61215• Designed to meet the requirements of IEC61730, including Safety Class II to IEC61140Naps Systems’ 30 years of solar power experience in all continents and conditions provide the highest level of quality and power in an attractive and dependable package. High power and efficiencyNaps Pallas series of solar modules contain 54 high efficiency dark blue polycrystalline solar cells. The cells are carefully selected to assure a narrow and positive power range, thus minimising mismatch losses in the system.Dependable construction and long lifeFeaturing the highest standards of construction and materials, Naps Pallas solar modules are able to withstand the harshest environments and continue to perform efficiently. Properly installed, these modules have a design life well beyond the power warranty. Limited power warranties are given for both 10 and 25 years. The modules are tested to meet or exceed all relevant international standards and the highest requirements for quality and performance. www.napssystems.com68º04’30”N Pallas 24º03’13”EPallas200-210GSAWGlass type: Frame colour: Backsheet colour:SMOOTH ALU WHITESAWSpecifications may change without notice due to Naps’ policy of continuous product development. Please confirm current specification before purchase. All product rights belong exclusively to Naps Systems Ltd. DS/Pallas SAW/EN/2/10_2000 35362.5740362.5D4 x 2943986146521.5D7 x 4Specifications: Naps Pallas 200-210G SAW1 kW/m2 IRRADIANCE, VARYING CELL TEMPERATURE (°C) (TYPICAL FOR PALLAS 200G SAW)012345678920304050607080Amps10 20 30 400VoltsAmps25°C CELL TEMPERATURE, VARYING IRRADIANCE (W/m2) (TYPICAL FOR PALLAS 200G SAW)012345678910 20 30 4010008006004002000VoltsAmps1 kW/m2 IRRADIANCE, VARYING CELL TEMPERATURE (°C) (TYPICAL FOR PALLAS 200G SAW)012345678920304050607080Amps10 20 30 400VoltsAmps25°C CELL TEMPERATURE, VARYING IRRADIANCE (W/m2) (TYPICAL FOR PALLAS 200G SAW)012345678910 20 30 4010008006004002000VoltsAmpsMechanical DetailsOverall length (mm) ........................................................ 1465Overall width (mm) ........................................................... 986Area (m2) ....................................................................... 1.444Thickness at edge (mm) ..................................................... 35Weight (kg) ...................................................................... 19.4ConstructionCell type ...........................................................polycrystallineCells ................................................................................... 54Cell dimensions (mm) ..............................................156 x 156Cell electrical circuit (series x parallel) ..........................54 x 1Cell layout (horizontal x vertical)......................................6 x 9Glass thickness (mm) ........................................................ 4.0Junction box type.................................................S PV1410-2Bypass diodes factory fitted ................................................. 3Cables (4.0 mm2) .........................................................2 x 1 mConnector type ............................ H+S Radox push-pull 4mmOther connector options available to special orderProtection ClassIEC61730 Application Class A, equivalent to Safety Class IIMaximum System VoltageVoltage (V) ...................................................................... 1000 Overcurrent ProtectionSeries fuse protection rating (A) ......................................... 15Reverse current maximum (A)............................................ 15Mechanical LoadTested to (N/m2 = Pa) ..................................................... 5400According to IEC 61215-2 extended test for heavy snow loadTemperature Coefficients at STC typeOpen circuit voltage (V/K)............................................. -0.120 Short circuit current (A/K) ............................................ 0.0039Maximum power (%/K) ................................................... -0.54Efficiency Reduction from STCReduction (approximately) (%) ............................................. 5Cell temperature (oC) .......................................................... 25Irradiance change (W/m2) ............................ from 1000 to 200Air Mass ............................................................................. 1.5STC = Standard Test ConditionsCell temperature (oC) .......................................................... 25Irradiation (W/m2) ............................................................ 1000Air Mass ............................................................................. 1.5NOCT = Normal Operating Cell TemperatureCell temperature (oC) .......................................................... 46Irradiation (W/m2) .............................................................. 800Ambient temperature (oC) ................................................... 20 Wind speed (m/s) ................................................................. 1Free air access to module rear Voltage / Current Dependence on TemperatureVoltage / Current Dependence on IrradianceModule DimensionsNaps Systems Ltd • Pakkalankuja 7, FI-01510 Vantaa, Finland Tel. +358 20 7545 666 • sales@napssystems.com • www.napssystems.comMade in EUPerformance at STC 200G SAW 205G SAW 210G SAWProduct code N00359 N00360 N00361Maximum power (W/Pmax) 200 205 210Maximum power tolerance (W) +5/-0 +5/-0 +5/-0Current (typical at max power) (A/Ip) 7.70 7.89 8.07Voltage (typical at max power) (V/Vp) 26.0 26.0 26.0Short circuit current (typical) (A/Isc) 8.35 8.52 8.69Open circuit voltage (typical) (V/Voc) 33.3 33.3 33.4 Module efficiency (minimum) (%) 13.8 14.2 14.5Module efficiency (maximum) (%) 14.2 14.5 14.9Performance at NOCT and 800 W/m2 200G SAW 205G SAW 210G SAWMaximum power (W/Pmax) 143.7 147.5 151.2Current (typical at max power) (A/Ip) 6.11 6.26 6.42Voltage (typical at max power) (V/Vp) 23.5 23.5 23.6Short circuit current (typical) (A/Isc) 6.76 6.89 7.03Open circuit voltage (typical) (V/Voc) 30.4 30.5 30.6