S-5-E - Mini Clamp Brochure

The S-5-E clamp is secured with our patented round-point setscrews without piercing the metal roof panel, thereby preserving the roof's warranties®®®The right way to attach almost anything to metal roofs S-5-E and S-5-E Mini888-825-3432 | www.S-5.com S-5-E ClampThe S-5-E clamp is designed specially for double-folded standing seam dimensioning.Although a bit smaller and less expensive than the S-5-U, for these The S-5-E is perfect for use with S-5® ColorGard® snow retention systems and other heavy-duty applications.Installation is as simple as placing the clamp on the seam and tightening the patented round-point setscrews to the items using the bolt provided. Go to www.S-5.com/tools for information and tools available for properly attaching and tensioning S-5 clamps.S-5-E Mini ClampThe S-5-E Mini is a bit shorter than the S-5-E and has one setscrew rather than two. The Mini is the choice for attaching all kinds of rooftop accessories: signs, walkways, satellite dishes, antennas, rooftop lighting, lightning protection systems, solar arrays, exhaust stack bracing, conduit, condensate lines, mechanical equipment—just about anything**S-5 Mini clamps can be used with RamGard® unitized snow guards but are not compatible and should not be used with our SnoRail™/SnoFence™ or ColorGard® snow retention systems.Distributed byS-5® Warning Please use this product responsiblyProducts are protected by multiple U.S. and foreign patents. Visit the website at www.S-5.com for complete information on patents and trademarks. For maximum holding strength, setscrews should be tensioned and re-tensioned as the seam material compresses. Clamp setscrew tension should be and between 130 and 150 inch pounds for all other metals and thinner gauges of steel. Consult the S-5 website at www.S-5.com for published data regarding holding strength.Copyright 2011, Metal Roof Innovations, Ltd. S-5 products are patented protected. S-5 aggressively protects its patents, trademarks and copyrights. The strength of the S-5-E clamp is in its simple design. The patented setscrews will slightly dimple the metal seam material but will not puncture it.S-5-E Mini ClampS-5-E ClampPlease note: All measurements are rounded to the second decimal place.The S-5-E and S-5-E Mini clamps are each furnished with the hardware shown to the right. Each box also includes a bit tip for tightening setscrews using an electric screw gun. A structural aluminum attachment clamp, the S-5-E excluding copper. All included hardware is stainless steel. Please visit www.S-5.com for more information including CAD details, metallurgical compatibilities and The S-5-E and S-5-E Mini have been tested for load-to-failure results on a variety of double-folded standing seam roofs, from leading manufacturers of panels and panel-forming machines. The independent lab test reports found on our website at www.S-5.com prove that S-5 holding strength is unmatched in the industry. Hardware shown is included with each clamp. For horizontal seams under .5" crimp the seam to 180 degrees at desired clamp location.This illustration demonstrates crimping technique, NOT actual location of clamp.= .5” Hardware shown is included with each clamp. 1.97" (50.00 mm)0.98" (25.00 mm)1.97" (50.00 mm)0.60" (15.00 mm)M10 holeslocated 13.00 mm (0.50") from edges of part1.97" (50.00 mm)0.98" (25.00 mm)1.18" (50.00 mm)0.30" (7.60 mm)0.60" (15.00 mm)M8 holecentered on part0.35" (8.90 mm)0.30" (7.60 mm)0.35" (8.90 mm)ADVANCED GREEN TECHNOLOGIES888.735.2641www.AGT.com