SES - 405M - Photovoltaic Module Datasheet

Our latest generation of small area modules offers the following benefits:Built to lastFrom mountaintops to off-shore platforms, on weather stations in the bitter cold of Antarctica and on telephone signal repeaters in the hot Australian outback, the technology has been proven in the harshest environments.Multiple mounting possibilities Multimount frame allows even greater flexibility in mounting. Positioned parallel to the edge and back of the module, its dual channels accept either M8 or 5/16” hex-head bolts, allowing the module to be mounted from the side or back.Easier bolt managementBolts may be located anywhere along the channels; the channel groove is specially designed to prevent the bolt from rotating when tightening, allowing installation with just one wrench.Long cable for easier battery connections. A 4.6 meter PVC- jacketed AWG 18- 2 polarized cable is potted into the fully sealed junction box located on the module back. The module’s electrical connections are sealed for prevention against corrosion and moisture penetration.4.5W Photovoltaic module405MModule appearance may vary. Cells have rounded corners with either 165 or 150mm diameter.Electrical characteristics(1) STC 1000W/m2(2) NOCT800W/m2Maximum power (Pmax) 4.5W 3.2WVoltage at Pmax (Vmpp) 16.5V 14.7VCurrent at Pmax (Impp) 0.27A 0.22AShort circuit current (Isc) 0.3A 0.24AOpen circuit voltage (Voc) 20.5V 18.7VModule efficiency 6.7%Tolerance Pmax ± 10%Nominal voltage 12VEfficiency reduction at 200W/m2 <5% reduction (efficiency 6.3%)Limiting reverse current 0.3ATemperature coefficient of Isc 0.105%/ °CTemperature coefficient of Voc -0.360%/ °CTemperature coefficient of Pmax -0.45%/ °C(3) NOCT 47 ±2 °CMaximum series fuse rating 1AApplication class Class C (according to IEC 61730-2007)Maximum system voltage 50V1: Values at Standard Test Conditions (STC): 1000W/m2 irradiance, AM1.5 solar spectrum and 25°C module temperature2: Values at 800W/m2 irradiance, Nominal Operation Cell Temperature (NOCT) and AM1.5 solar spectrum3: Nominal Operation Cell Temperature: Module operation temperature at 800W/m2 irradiance, 20°C air temperature, 1m/s wind speedAll solar modules are individually tested prior to shipment; an allowance is made within our factory measurement to account for the typical power degradation (LILD effect) which occurs during the first few days of deployment.SES MAPPS Solar Module Mechanical characteristicsSolar cells 36 monocrystalline silicon cut cells connected in seriesFront cover High transmission 3.2mm (1/8“) glassEncapsulant EVABack cover White polyesterFrame Silver anodized aluminumJunction box Lo-Pro junction box Output cablesAWG#18 (0.75mm2) 2 core, ITC / PLTC Lengths 4572mm / 15 ft.(“+” red; “-” black)Dimensions 251 x 269 x 23mm / 9.9 x 10.6 x 0.9in Weight 0.8kg / 1.7lbsAll dimensional tolerances within ±1% unless otherwise stated.Warranty*• Free from defects in materials and workmanship for 2 years• 90% Min power output for 12 years • Optional 25 years available *Refer to limited warranty certificate for terms and conditionsSES MAPPS Solar Module Certification Listed to UL 1703 & ULC ORD-C1703 Standard for Safety by Intertek ETL. Class C Fire Rating.Approved by Intertek ETL according to FM 3611, Dec 2004, and according to CAN/CSA C22.2 No. 213-M1987, 1st Edition, Reaffirmed 2004, for use in a Class I Division 2, Group A, B, C, D Hazardous (Classified) Location.4.5W Photovoltaic module – 405M © Solar Electric Supply, Inc. May 2012Toll Free: 877-297-0014Phone: 831-462-8243 • Fax: 831-462-8246Email: contact@solarelectricsupply.comwww.solarelectricsupply.com