Sliding Vane Pumps-GX Model

X2-HRX2 cutawayGX3GX CutawayGX & X SeriesGeneral Duty PumpsSpec Sheet 101-003Section: 101Effective: January 2012Replaces: November 2009DesignBlackmer’s GX and X series models are available in 2, 2.5, 3 and 4-inch flanged port sizes with capacities from 30 to 520 U.S. gpm (114-1,855 L/min). Cast iron construction is standard on all models except the X4 model which is ductile iron construction. All models have external ball bearings isolated from the pumpage by mechanical seals. The GX type pumps feature an integral head-mounted gear reduction drive with oil lubricated, hardened helical gears that provide quiet trouble-free operation. Gear shafts are supported at both ends by ball bearings for smooth operation and long life. A splined shaft simplifies alignment of the pump and reducer, and the reducer can be rotated on the pump head to accommodate a variety of motor sizes without shimming.ApplicationBlackmer’s GX and X type pumps are designed to handle a wide range of non-corrosive, non-abrasive industrial liquids and petroleum products. Typical applications include fuel oils, lube oils, jet fuels, gasoline, edible oils and a variety of solvents and thinners such as esters, ketones, naphthas, ethers, amines, aromatics, alcohols, terpenes, glycols and many other similar liquids.BenefitBlackmer’s positive displacement rotary pumps utilizing their unique sliding vane design offers the best combined characteristics of sustained high level performance, energy efficiency, trouble-free operation and low maintenance cost. Also, the high suction lift capability of these pumps makes them especially suitable for pumping from underground tanks, bulk plant service and aircraft refueling.How Blackmer’s sliding vane action worksPump Model A B C D E F G H J K L M NApprox. Wt. with Std. FlangesGX2in. 3/4 3/16 119/16 53/8 811/16 31/2 4 11/2 93/4 4 41/8 15/8 5 110 lbs.mm – – 294 137 221 89 102 38 248 102 105 41 127 50 kgGX2.5in. 3/4 3/16 125/16 6 95/8 33/4 45/16 13/4 1011/16 4 51/16 3 51/2 130 lbs.mm – – 313 152 244 95 110 44 271 102 129 76 140 59 kgGX3in. 1 1/4 141/2 61/2 123/16 45/8 5 21/2 133/8 53/8 51/4 21/2 6 230 lbs.mm – – 368 165 310 117 127 64 340 137 133 64 152 104 kgGX4in. 11/8 1/4 185/8 81/8 151/2 5 73/8 21/2 167/8 63/8 8 41/2 8 430 lbs.mm – – 473 206 394 127 187 64 429 162 203 114 203 195 kgPump Model A B C D E F G H J K L M NApprox. Wt. with Std. FlangesX2in. 11/8 1/4 8 53/8 811/16 31/2 4 11/2 93/4 4 41/8 15/8 5 110 lbs.mm – – 203 137 221 89 102 38 248 102 105 41 127 50 kgX2.5in. 11/8 1/4 83/4 6 95/8 33/4 415/16 13/4 1011/16 4 51/16 3 51/2 130 lbs.mm – – 222 152 244 95 110 44 271 102 129 76 140 59 kgX3in. 11/8 1/4 95/8 61/2 123/16 45/8 5 21/2 133/8 53/8 51/4 21/2 6 230 lbs.mm – – 244 165 310 117 127 64 340 137 133 64 152 104 kgX4in. 11/2 3/8 11 81/8 151/2 5 73/8 21/2 167/8 63/8 8 41/2 8 430 lbs.mm – – 280 206 394 127 187 64 429 162 203 114 203 195 kg** ANSI Compatible flanges are Raised Flat Faced.1 GX pump models are limited by gear reducer capability (pressure / rpm / viscosity dependent).2 Flow is normal at 50 psi (3.45 bar) differential pressure.3 Viscosity listed is maximum. Blackmer GX and X pump models are also well suited for viscosities less than 31 ssu (1 cSt).4 Centipoise (cP) = Centistokes (cSt) at fluid specific gravity of 1.0Note: Optional materials of construction may be required to meet specific application requirements – refer to Blackmer Material of Construction Sheet 101-095.Printed in USA © 2012 BlackmerProcess | Energy | Military & MarineWorld Headquarters1809 Century Avenue SW, Grand Rapids, MI 49503-1530 USAT 616.241.1611 F 616.241.3752 www.blackmer.com Performance Data*Pipe Companion FlangesMaximum Operating LimitsPump Model GX2, X2 GX2.5, X2.5 GX3, X3 GX4, X4Rated Pump Speed (rpm) 640 520 420 350 640 520 420 350 640 520 420 350 500 400 300 230 190U.S. gpm 70 55 44 36 121 96 76 63 270 220 177 146 507 404 299 225 190L/min 264 210 165 135 461 363 288 237 1023 835 671 544 1919 1532 1135 855 695hp 3.2 2.6 2.0 1.7 4.7 3.7 2.9 2.4 11.2 8.5 6.5 5.2 20.8 15.9 11.5 8.6 7.0Pump Model Standard OptionalGX21, X2 2" NPT2" Blackmer Weld2" ANSI**GX2.5, X2.5 2.5" NPT2.5" Blackmer Weld3" ANSI**GX3, X3 3" NPT3" Blackmer Weld3" ANSI**GX4, X4 4" NPT4" Blackmer Weld4" ANSI**Pump Model Maximum Pump Speed Minimum Pump Speed MaximumDifferentialPressure MaximumWorkingPressure MaximumOperatingTemperatureSpeed Flow2 Viscosity3 Speed Flow2 Viscosity3rmp gpm (L/min) ssu (cSt) 4 rpm gpm (L/min) ssu (cSt) 4 psi (bar) psi (bar) °F (°C)GX21 780 87 (329) 100 (22) 190 20 (76) 20,000 (4,250) 125 (8.6) 175 (12.1) 300 (149)X2 780 87 (329) 100 (22) 68 7 (26) 20,000 (4,250) 125 (8.6) 175 (12.1) 300 (149)GX2.5 780 155 (587) 100 (22) 190 33 (125) 20,000 (4,250) 125 (8.6) 175 (12.1) 300 (149)X2.5 780 155 (587) 100 (22) 68 12 (45) 20,000 (4,250) 125 (8.6) 175 (12.1) 300 (149)GX31 640 270 (1,022) 100 (22) 125 46 (174) 20,000 (4,250) 125 (8.6) 175 (12.1) 300 (149)X3 640 270 (1,022) 100 (22) 68 28 (106) 20,000 (4,250) 125 (8.6) 175 (12.1) 300 (149)GX41 520 528 (1,999) 100 (22) 100 90 (341) 20,000 (4,250) 125 (8.6) 175 (12.1) 300 (149)X4 520 528 (1,999) 100 (22) 68 66 (250) 20,000 (4,250) 125 (8.6) 175 (12.1) 300 (149)* Approximate capacities and horsepower (HP) are based on a 100 ssu (22 cSt) fluid at a 50 psi (3.45 bar) differential pressure. Refer to Characteristic Curves for capacities and horsepower at other pressures and viscosities. Centipoise (cP) = Centistokes (cSt) at fluid specific gravity of 1.0Dimensions2/12 - 1MGX Pump ModelsDCBAMGX and X Pump ModelsEFGNKLHJCBAMD