Soft-Starter SSW-05 Brochure

g Tough g Reliableg Durableg QualityUSASSW0509Motors | Automation | Energy | Coatings SSW05Soft Starter www.weg.net2 1-800-ASK-4WEGApplications* g Pumpsg Fansg Blowersg CompressorsThe WEG SSW05 Soft Starter is a super compact fully digital soft starter with a state-of-the-art DSP controller. Its digital construction provides optimum operation, diagnostics capability and full motor protection. Simplicity in set-up and operation is assured since all parameters and set-up selections are made via dip switches and potentiometers. Status LED’s alert the user of the operational status of the SSW05. Simplicity, ease of set-up, and the micro size assures quick and easy installation and operation.Standard Features g 208 - 480V, 50/60Hz input power supplyg Duty cycle: 300% rated current during 10 seconds, 4 starts per hourg Built-in bypassg One digital input for Start/Stop (90 - 250 Vac)g One digital input for Fault Reset (90 - 250 Vac)g One relay output for Run indication (1 Amp - 250V)g One relay output for Full Voltage indication (1 Amp - 250V)g RS-232 serial portg Adjustable acceleration and deceleration ramps (1 - 20 seconds)g Adjustable pedestal voltage (30 - 80% of line voltage)g Protective features: Motor overload, over current and lo-cked rotor, SCR overload, phase loss and phase sequenceg DIN rail or direct mountg Ambient: 32ºF (0ºC) to 131ºF (55ºC), 3300ft (1000m) alti-tude, 90% non-condensing humidityOptional Features g Remote Keypadg PC Programming SoftwareSoft Starters SSW05 * For high inertia loads, see SSW07 product line.WEG Automation - Products and Solutionswww.weg.net3SSW05 – AccessoriesMotor Volts Motor HP Soft Starter AMPS Catalog Number Frame SizeDimensions (in.) H x W x DApp. Shpg. Wt. (lbs.)230VINPUT POWER SUPPLY: THREE-PHASE - 230V3 10 SSW050010T2246EPZ 1 5.1 X 2.3 X 5.7 35 16 SSW050016T2246EPZ 1 5.1 X 2.3 X 5.7 37.5 23 SSW050023T2246EPZ 1 5.1 X 2.3 X 5.7 310 30 SSW050030T2246EPZ 1 5.1 X 2.3 X 5.7 315 45 SSW050045T2246EPZ 2 7.3 X 3.1 X 6.8 620 60 SSW050060T2246EPZ 2 7.3 X 3.1 X 6.8 630 85 SSW050085T2246EPZ 2 7.3 X 3.1 X 6.8 6460VINPUT POWER SUPPLY: THREE-PHASE - 460V5 10 SSW050010T2246EPZ 1 5.1 X 2.3 X 5.7 310 16 SSW050016T2246EPZ 1 5.1 X 2.3 X 5.7 315 23 SSW050023T2246EPZ 1 5.1 X 2.3 X 5.7 320 30 SSW050030T2246EPZ 1 5.1 X 2.3 X 5.7 330 45 SSW050045T2246EPZ 2 7.3 X 3.1 X 6.8 640 60 SSW050060T2246EPZ 2 7.3 X 3.1 X 6.8 660 85 SSW050085T2246EPZ 2 7.3 X 3.1 X 6.8 6Notes:1) “HP” rating based on Table 430-150 of the NEC. Use as a guide only. Motor FLA may vary with speed and manufacturer.ALWAYS compare motor FLA to Nominal AMPS of starter.2) 120V Control Power Supply required.3) For other technical data please refer to WEG product manual.Soft StartersSSW05Protected Chassis EnclosureDescription Catalog NumberRemote Keypad with LED Display HMI-SSW05-RS3.3 ft. Remote Keypad Cable CAB-RS-16.6 ft. Remote Keypad Cable CAB-RS-210 ft. Remote Keypad Cable CAB-RS-315 ft. Remote Keypad Cable CAB-RS-525 ft. Remote Keypad Cable CAB-RS-7.533 ft. Remote Keypad Cable CAB-RS-10Data is subject to change without notice.Settings and IndicationsOpen View PanelDip-switches to enable/disable motor protectorsPotentiometers for Pedestal Voltage, Accel/Decel time andMotor Overload adjustmentsControl Power Supply and Digital InputsLEDs to indicate fault tripsLEDs to indicate starter statusRelay Outputswww.weg.netPower Supply Main Voltage 220 ... 460 Vac (+10%, -15%)Control Voltage 90 ...250 VacFrequency 50 / 60Hz (+/- 5Hz)EnclosureDuty CycleControl Inputs Digital One input for Start/Stop (90 - 250 Vac)One input for Fault Reset (90 - 250 Vac)Control Outputs Digital One relay output for Run indication (1 Amp - 250V)One relay output for Ful Voltage indication (1 Amp - 250V)Communication Serial Interface RS-232CSafety Protections Motor overload*Locked rotor*Over current*Phase sequence*Phase loss** Can be disabled SCR overloadControl Features Pedestal Voltage 30 … 80% of line voltageAccel Ramp 1 ... 20 secondsDecel Ramp Off ... 20 secondsMotor Current 30 ... 100% of SSW-05 ratingFault Reset Manual or AutomaticAmbient Temperature 32 ... 131ºF (0 - 55ºC)Humidity 0…90% Non CondensingAltitude 0 ... 1000m (3,300 ft) - Standard Operation at Rated CurrentUp to 4000m (13,200 ft) - With Current Derating (1%/100m (328 ft) above 1000m (13,200 ft) )Conformities Low Voltage UL 508 - Industrial Control EquipmentIEC 60947-4-2EMC EMC Directive 89 / 336 / EEC - Industrial Environ-ment, Class ASoft StartersSSW05SSW05 – Technical DataIP00 Protected Chassis300% rated current during 10 seconds, 4 starts per hourWEG Electric Corp.1327 Northbrook Parkway, Suite 490Suwanee, GA 30024Phone: 1-800-ASK-4WEG web: www.weg.netUSASSW0509Please contact your authorized distributor: