low temperature waste heat Articles

  • Marketing Analysis of Low Temperature Waste Heat Boiler

    Environmental pollution brought by the burning of fossil fuels and improper energy use structure have became big problems of boiler manufacturer like ZG. To need the market demand for the development of new energy and renewab ...


  • Utilizing Waste Heat For Power

    Continuous duty gen-sets provide base-load power generation in diverse applications around the globe. However, high fuel costs and engine maintenance are pain points felt by operators. A low-maintenance path to significant fuel savings and lower emissions is what the U.S. Department of Defense (DOD) had in mind when they approached ElectraTherm to integrate the company’s Green Machine waste ...


    By ElectraTherm

  • Case study - Waste heat generates steam and savings

    OVERVIEW A coil coating facility purchased a new a 15,000 SCFM Regenerative Thermal Oxidizer (RTO) which had a nominal heat transfer efficiency rate of 90% thermal energy recovery. It was designed with supplemental fuel injection (SFI) which is used during low VOC loading conditions, to help save fuel cost.  The facility was looking for additional ways to decrease their exhaust ...

  • Case-study - Utilising waste heat for water production and climate control

    Water purification is needed to produce high quality water for consumption, agriculture and industrial needs. Conventional water treatment processes, like distillation and reverse osmosis, consume vast amounts of energy. However, there is a large potential for significant reductions in energy consumption and CO2 emissions in this sector. It can be achieved by the exploitation of waste heat for ...


    By Climate-KIC

  • Performance of the low-emission flare

    Job report / Elbisgraben (Bale / Switzerland) The summer of 1992 had finally arrived. The 5MW low emission furnace in the district heating station Liestal was ignited, supplied with landfill gas from Elbisgraben landfill. Since then the plant has been running continuously and the comprehensive measurements taken, verify that all targets aimed at have been achieved: plant ...


    By Hofstetter BV

  • Heat Pumps – FAQs

    1. What is a Heat Pump? To put it simply; ground source heat pumps and geothermal heat pumps produce high grade heat from low grade heat which is found in the earth and our atmosphere.2. How does a Heat Pump Work?Heat pumps work in exactly the same way as air conditioners or refrigerators, but in reverse! Heat pumps capture latent energy which is stored in sources such as air, water and earth. ...


  • A road map for emerging low-exergy HVAC systems

    An exergy-conscious life cycle costing algorithm was developed. This algorithm establishes a reference tool to compare conventional air conditioning systems with alternative HVAC systems, which can directly operate with low-exergy alternative energy resources. The cost of exergy waste in conventional heating, ventilating, and air-conditioning systems (HVAC) is included in terms of the difference ...


    By Inderscience Publishers

  • Combined Heat and Power – Questions and Answers

     1. What are the benefits of CHP for business?   combined heat and power (CHP) is a well-proven technology, recognised worldwide as a cleaner alternative to traditional centralised generation. Its long-term future in the global energy markets is secured by CHP's ability to provide a multitude of financial, ...


    By ENER-G

  • Using biogas for combined heat and power

    An integral part of the majority of anaerobic digestion facilities across the world is the CHP combined heat and power (CHP) engine. For the first time builder of a biogas plant, it is often neglected as the focus is on reducing the capital costs ...


    By Clarke Energy

  • Using biogas for combined heat and power

    An integral part of the majority of anaerobic digestion facilities across the world is the CHP combined heat and power (CHP) engine. For the first time builder of a biogas plant, it is often neglected as the focus is on reducing the capital costs ...


    By Clarke Energy

  • Case study - Green Machine generates power from waste heat at biogas facility in the Czech Republic

    Biogas/Heat-to-Power Application on Two MWM Internal Combustion Engines Site: Brno, Czech Rep. Engine Max Power: 980kWe (currently limited to 900 kWe) Green Machine Gross Power Output Avg:  32-39 kWe Thermal Input to the Green Machine: 375-500kWt Hot Water Input Range: 86 - 92°C Hot Water Flow: 35 m3/hour Ambient Temperature: 0-25°C Date Commissioned: Q2 ...


    By ElectraTherm

  • Green machine generates power from waste heat at biogas facility in the Czech Republic

    Biogas/Heat-to-Power Application on Two MWM Internal Combustion Engines Site: Brno, Czech Rep. Engine Max Power: 980kWe (currently limited to 900 kWe) Green Machine Gross Power Output Avg:  32-39 kWe Thermal Input to the Green Machine: 375-500kWt Hot Water Input Range: 86 - 92°C Hot Water Flow: 35 m3/hour Ambient Temperature: 0-25°C ElectraTherm’s ...


    By ElectraTherm

  • Heat Recovery for Reuse in Proofing Ovens: Buttercup Bakeries

     By collaborating with a major tertiary research institution, RMIT University, Buttercup Bakeries has been able to apply new heat recovery technology suitable for bakery and other industrial applications. The initiative has resulted not only in cost and energy savings but more efficient oven heating boiler operations. Background Buttercup Bakeries is part of the ...


  • Energy Savings on Process Heating Units Case History

    The Customer This specialty chemical company is a leading supplier of performance polymers. Their products are used in a wide range of applications including adhesives, coatings, consumer and personal care products, sealants, lubricants, medical, packaging, automotive, paving, roofing and footwear products. The Project The company was increasing the ...

  • Saving waste in the boiler house

    Burner technology has improved greatly in recent years. Older Burners had a series of cams and levers that were calibrated to provide specific amounts of air for a particular rate of firing. Being mechanical items, these wore and sometimes required calibration. They, therefore, had to be regularly serviced and calibrated. Generally, new burners use frequency controlled motors and cams to open air ...


    By EBE Engineering Ltd.

  • Heat recovery and energy efficiency, improves profitability and reduces CO footprint

    Using latest technology in combustion of oil and gas can provide significant savings in overall energy consumption. Modern oxygen control that compensates changes in ambient temperature and fuel qualities can increase energy efficiency up to 3%. By adding the usage of hot combustion air another 2-3% can be saved. Modern burner technology without mechanical linkage, operating with accurate ...


    By Oilon Oy

  • Case study - ElectraTherm commissions 10 green machines on district heating system in Europe

    ElectraTherm commissioned 10 Green Machine 4400s in Levice, Slovakia in June 2014. ElectraTherm’s Czech distributor, GB Consulting, facilitated the deployment of Organic Rankine Cycle (ORC) systems on a centralized district heating system in Slovakia as a means of increasing on-site efficiency and generating clean energy. ElectraTherm’s Green Machine generates fuel-free, ...


    By ElectraTherm

  • High-strength wastes boost biogas production

    Water and wastewater treatment plants (WWTP) are significant consumers of energy. The U.S. Environmental Protection Agency estimates the industry uses the equivalent of 56 billion kilowatt hours (kWh) of electricity, representing three percent of the nation’s energy consumption, and is responsible for creating 45 million tons of greenhouse gas emissions each year. Energy intensive processes, such ...


    By BioCycle Magazine

  • Staged Thermal Treatment Combined With Pyrometallurgical Smelting Producing Energy and Products From Waste

    Incineration of waste is considered as a state-of-the-art technology. However staged gasification in combination with pyrometallurgical smelting is ready for market introduction and offers principal advantages. These are higher efficiency (up to 35% electricity), efficient and cheaper fuel gas cleaning (less emissions), high quality secondary products (synthetic basalt), high input flexibility, ...


  • Flooring manufacturer chooses catalytic products to reduce energy usage

    HEAT RECOVERY SYSTEM A leading floor covering manufacturer contracted Catalytic Products International, Inc. to design and install a heat recovery system that uses waste heat from their Regenerative Thermal Oxidizer. The system had to be very efficient since the energy available in the RTO exhaust was fairly low temperature. The other challenge was to design a useable system that returned heat to ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you