Refine by
material-testing books
18 books found
The symposium was sponsored by Committee C16 on Thermal and Cryogenic Insulation Materials of the American Society for Testing and Materials. R. P. Tye, Dynatech R/D Company, presided as symposium chairman and editor of this ...
The Symposium on Contributions of Basic Heat Transmission Measurements to the Design and Behavior of Thermal Insulation Systems was held at the American Society for Testing and Materials Headquarters in Philadelphia, Pa., on 16-17 April 1973. The symposium was sponsored by ASTM Committee C16 on Thermal and Cryogenic Insulating Materials. R. P. ...
The Symposium on Irradiation Effects on Structural Alloys for Nuclear Reactor Applications was presented at Niagara Falls, Canada, 29 June-1 July 1970, in conjunction with the Seventy-third Annual Meeting of the American Society for Testing and Materials held in Toronto, Ontario, Canada, 22-26 June 1970. ...
The test methods described in this publication have not been subjected to the ASTM Standardization Procedure. They are not standards or standard recommended practices of the American Society of Testing and Materials. However, these procedures are developed and approved by ASTM Committee D02 Technical Division B on Automotive Lubricants. ...
The test methods described in this publication have not been subjected to the ASTM Standardization Procedure. They are not standards or standard recommended practices of the American Society of Testing and Materials. However, these procedures are developed and approved by ASTM Committee D02 Technical Division B on Automotive Lubricants. ...
This conference was sponsored by the American Society for Testing and Materials (ASTM) Committee B10 on Refractory Metals and Alloys in cooperation with the American Nuclear Society, the British Nuclear Energy Society, and The Metals Society (U.K).. ...
It was sponsored by the American Society for Testing and Materials' (ASTM) Committee C-16 on Thermal and Cryogenic Insulating Materials in cooperation with the American Institute of Chemical Engineers (AIChE) and was presented during a meeting of AIChE. ...
This book is an introduction to the multidisciplinary field of anomalous diffusion in complex systems, with emphasis on the scaling approach as opposed to techniques based on the quantitative analysis of underlying transport equations. Typical examples of such systems are turbulent plasmas, convective rolls, zonal flow systems and stochastic magnetic fields. From the more methodological point of ...
This International Standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of steam turbines for special-purpose applications. ...
This International Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum and natural gas industries. ...
The Symposium on Gas Turbine Fuel Requirements, Handling and Quality Control was presented at the Seventy-fifth Annual Meeting of the American Society for Testing and Materials held in Los Angeles, Calif., 25—30 June 1972. ...
This volume features the latest standards on: Engine Coolants—standards cover the chemical and physical properties of engine coolants, dynamometer and road tests, glassware performance tests, and heavy-duty coolants. This section also includes specifications on glycol base engine coolants, recycled engine coolants, reference test ...
This International Standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air preheaters, fans and burners for general refinery service. ...
This part of ISO 15547 gives requirements and recommendations for the mechanical design, materials selection, fabrication, inspection, testing, and preparation for shipment of plate-and-frame heat exchangers for use in petroleum, petrochemical and natural gas industries. ...
This volume features the latest standards on: Engine Coolants—standards cover the chemical and physical properties of engine coolants, dynamometer and road tests, glassware performance tests, and heavy-duty coolants. This section also includes specifications on glycol base engine coolants, recycled engine coolants, reference test ...
This volume features the latest standards on: Engine Coolants—standards cover the chemical and physical properties of engine coolants, dynamometer and road tests, glassware performance tests, and heavy-duty coolants. This section also includes specifications on glycol base engine coolants, recycled engine coolants, reference test ...
This part of ISO 15547 gives requirements and recommendations for the mechanical design, materials selection, fabrication, inspection, testing, and preparation for shipment of brazed aluminium plate-fin heat exchangers for use in petroleum, petrochemical and natural gas ...
This International Standard specifies requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical and natural gas industries. ...