Refine by
Material Testing Articles & Analysis
19 articles found
It involves several sequential stages: design and engineering, material procurement, manufacturing, testing, shipping, and final installation. ...
in the process data and practical results. 1. Raw materials for testing Through the SRF alternative fuel preparation system developed by HarDen, the general industrial solid waste alternative fuel is prepared from waste clothing, waste corners and other textile waste. ...
Pyrolysis machines transform scrap materials into fuel that burns cleanly with hardly any smoke or toxins. ...
Formerly known as the American Society for Testing and Materials, ASTM has been setting a widely-recognized and revered standard for testing and evaluating materials for well over a century. ...
Metal contaminants can be introduced into the battery from the raw materials, or from the actual processing, i.e. metal particles from machinery. ...
The experimental work herein presented led to the identifi cation of pollutants emission minimisation during the co-combustion of coal with biomass origin material. In the tested mixtures, coal was replaced by 5%, 15% and 25% of RES material and the tests were done in two FB pilots of different nominal capacities (70kWth and ...
The varied use of the buildings for activities such as material testing labs with climate chambers and gymnastic halls for student leisure, makes for a challenging task in the daily routine of the operations team. ...
The OECD 308 water‐sediment transformation test has been routinely conducted in Phase II Tier A testing of the environmental risk assessment (ERA) for all human pharmaceutical marketing authorization applications in Europe since finalization of Environmental Medicines Agency (EMA) ERA guidance in June 2006. In addition to the ‘Ready Biodegradation’ ...
A natural convection solar tunnel drier integrated with rock bed as sensible heat storage material was developed to test its performance for copra drying. The experiments were carried out with and without the integration of heat storage material. ...
The Japan Materials Testing Reactor (JMTR) loaded the 4.8 g/cc silicide fuel for the core conversion from the high to the low enrichment (94°C). The safety margin of the JMTR against the accident induced by the abnormal withdrawal of control rod was assured.Keywords: transient behaviour, silicide fuel, abnormal withdrawal, control rods, JMTR, Japan ...
In case of Pongamia pinnata, purified ester yields at 50°C were 79% for 4 hr and 83% for 6 hr. Further, when the fuel was tested for its authenticity to be used in diesel engine based on the American Society for Testing and Materials (ASTM), it was found that the fuel was coming within the prescribed standards. ...
Silicon carbide has been identified as the preferred construction material. Its stability is tested at high temperature and in a highly corrosive atmosphere. ...
The effects of intensive fluxes of neutrons, thermal ageing or other external factors result in considerable changes of material microstructures and properties. In particular, the development of the fine scale radiation-induced defects which impede the dislocation motion under the applied stress, known as the irradiation embrittlement, leads to mechanical properties degradation ...
One of the most important safety considerations is the integrity of the RPV (Reactor Pressure Vessels). The RPV material suffers several ageing-related effects during operating service: neutron (and gamma) irradiation embrittlement, thermal ageing, low-cycle fatigue, thermal fatigue and corrosion. ...
For all solutions, a 1 μCi/mL dilution in deionized water was prepared from the stock solutions. Coupon materials This testing matrix utilized four types of coupons including concrete, carbon steel, stainless steel and Plexiglas. ...
The third one is a pilot project using TES in micro-encapsulated phase change materials in a test cabin in Adana with a floor area of 4 m². By using a 3.5 kg Phase Change Material (PCM) together with insulation panels in the test cabin, 7% cooling energy and 28% heating energy can be conserved. The corresponding CO2 emissions ...
An indirect forced convection solar drier integrated with heat storage material was developed to test its performance for copra drying. The drier consists of a solar flat plate air heater integrated with a sensible heat storage unit, a drying chamber and a centrifugal blower. The experiments were carried out with and without the integration of heat storage ...
Global emission regulations for dieselpowered on- and off-road equipment present engine manufacturers with a dual challenge: First is the requirements for testing and evaluation of new components and new engine designs that will place unprecedented demands on the industry’s emissions testing facilities. ...
Comprehensive programmes were implemented of RMS and GS elements investigation, material studies (including testing of cut-off samples) and forecast of properties until the total life of 45 years. ...