GPE Energy Industry Equipment
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
The Model 31850 LED Edge Guide Sensors are specifically designed for strip guiding applications where maximum versatility is required. The sensor is available in standard gap (10' maximum) or wide gap (20' maximum) housing configurations for any application. Either housing configuration is extremely durable. Both sensors consist of two separate housings that contain the light source and the ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Double end, low by-pass leakage, 1 1/2" - 8" bore, bronze bearings, up to 1500 lbs, chrome plated cylinder rod, foot, flange, or pivot ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
The Model 31581 Autowide Centerguide Sensor is designed specifically to provide continuous scanning of the entire span of strip width variations. This eliminates operator adjustments for strip width changes. The sensor consists of two light source housings and two solar cell housings. 250 watt lamps are used as the light source and the number of lamps required is determined by the detector ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Proportional Adjustable Ration Control, Pressure, DP, or Electronic Input, Uses Common Power Supply, Spindle, Slide, Bell Crank, or Geared Wheel Ration Adjusters, 235 to 45,000 lbs. of ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
The Model 13210 Proportlonal-Plus-Reset Hydraulic Controller Is designed for slow-reacting control applications that require stability. A group of controllers are supplied from a separate, but common power supply. The controller has a practical output range of approximately 235 to 45,000 pounds of force at the actuator. Model 13210 accepts pressure or differential ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Five Gallon Reservoir, 125 to 230 PSI, Mounting for Two Controllers, External Pump for Easy Maintenance, 1/2 Horsepower Pump, Meets JIC Standards, 0.8 to 4.0 ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Integral Motor / Pump, Low Inertia / Torque Ratio, Same options as 13x10 Models, Simplicity of Design, High Speed ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Meets JIC Standards, 5 to 15 Horsepower, 500 to 900 PSI, 60 Gallon Reservoir, 10 to 20 ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
The Model 31551 Heavy Duty Edge Guide Sensor is specifically designed for heavy duty strip guiding applications, where maximum versatility is required. The sensor consists of two sturdy cast steel housings which are mounted separately, providing greater installation flexibility. One housing contains the photocell and is available in two options, either photoresistive (cadmium sulfide) or ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Integral Power Supply, Pressures up to 1000 psi, 10 to 40 GPM, 10 to 25 Horsepower, 100 Gallon Reservoir, Proportional Control, Pneumatic or Electronic Inputs, Manual or Automatic ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Ten Gallon Reservoir Eliminates the Need for Heat Exchanger, Pressure, Filter, and Level / Temperature Switches, Meets JIC Standards, 3.7 GPM, 100 to 300 ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Integral Power Supply, Pressures up to 930 psi, 5.8 to 14.1 GPM, 3 to 7.5 Horsepower, 35 Gallon Reservoir, Proportional Control, Pneumatic or Electronic Inputs, Manual or Automatic ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Proportional Control, Pressure, DP, or Electronic Input, Uses Common Power Supply, Spindle Set Point Adjusters, 235 to 45,000 lbs. ...
-
Manufactured by Shand & Jurs (L&J Technologies & L&J Engineering)based in USA
Single End, Low By-Pass Leakage, 1 1/2' - 8' Bore, Bronze Bearings, Up to 1500 lbs, Chrome Plated Cylinder Rod, Foot, Flange, or Pivot ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you