Monarch Instrument - Model ACT-3X -Panel Tachometer with NIST Traceable Certificate

All models - Universal Input, non-contact operation from optical, infrared, laser, proximity, and magnetic sensors or direct TTL and 200 mV to 50 V ac signals

ACT-3X Panel Tachometer

• 1/8 DIN sized
• 5-digit LED display
  
• 5 to 999,990 RPM range
• Universal sensor inputs
• NIST Traceable Certificate included
• User-configurable with front panel pushbuttons or free downloadable PM Remote Software
• View real-time data on PC*
• Record data in .CSV format in real time*
• Universal ac power 100-240 V ac, 50/60 Hz or optional 12 or 24 V dc power
• Standard pulse repeater output
• Single event capture from start-stop pulses, in units such as MPH, CM/sec, etc. using two sensors - for the linear rate of travel on the second input channel
• Optional 4-20 mA or 0-5 V dc scalable output
• Optional Ethernet or USB communications
• Optional alarm relay outputs

*If no communications option is ordered, requires USB programming cable and PM Remote Software (free download)

• Speed Range: 5-999,999 RPM (speeds below 5 RPM possible with multiple pulses per revolution)
• Input Frequency Range: 0.083 Hz to 80 kHz
• Totalizer/Counter: Display Range: 0.001 to 99,999
• Input Configuration: Universal inputs: 1 to 9,999 pulses per revolution
• front panel pushbutton programmable TTL input and 1.1 V to 50 V ac signals, Opt: -1 to -50 V dc
• Accuracy: +/-0.001% of reading or +/-1 displayed resolution (standard gate),
• +/-0.06% of reading or +/-1 displayed resolution (fast gate)
• Resolution: Up to 0.001 RPM, 10 RPM (100,000 to 999,990 RPM)
• Display: 5-digit, 0.56 in. [14 mm] high red LED
• Display and Output Update: Menu-selectable between 0.5 seconds above 120 RPM, 1 second above 60 RPM, and 1.5 seconds above 40 RPM
• Max Measurement Rate: Up to 100 times per second (Standard Gate) or up to 1000 (Fast Gate) dependent on the input frequency; input must be measurement rate
• Scaling: Programmable scaling: 0.0001 to 9999.9 (front panel pushbutton programmable)
• Decimal Point: User-selectable (0-3) decimal places max (front panel pushbutton programmable)
• Memory: Maximum, minimum, and last reading recall from front panel pushbuttons
• Dimensions: 1/8 DIN by 4.5 in. [114 mm] deep
• Panel cutout: 3.58 in. x 1.74 in. [91 x 44 mm]
• Input Power:
• Standard: 100-240 V ac +/-10%, 50/60 Hz
• Optional: 12 or 24 V dc +/-20%, isolated, 8VA
• Inputs: Universal input for optical, proximity, two-wire or three-wire magnetic, infrared, or laser sensors; TTL input or 3.3 V ac to 50 V ac input (The standard input is 1 pulse per revolution.)
• Sensor Excitation: 5 V dc or optional 12 or 24 V dc to sensor
• Recommended Sensors:
• LED - ROS-W
• High Temp - ROS-HT-W-25
• Proximity - P5-11, PS-12
• Magnetic - M-190W or MT-190W
• Infrared - IRS-W
• Laser - ROLS-W, RLS-W, SLS-115/230, CSLS
• Inductive - GE200-HP Gas Engine (requires amplifier)
• Pulse Repeater Output:
• Standard, 0 to 5 V TTL compatible; one pulse out for each pulse in
• Menu-selectable polarity
• Communications: Bidirectional RS232C, USB, or Ethernet interface
• Analog Output (optional):
• Voltage (AO): 0 to 5 V dc, 5 mA max load (isolated or non-isolated) or Current (IO): 4 to 20 mA, 500 ohm,¦ max load. (or non-isolated), 1 to 5 V dc possible using 250 ohm resistor) 16-bit resolution
• Front panel pushbutton programmable for full scale and offset RPM ranges
• Pulse Output (optional): Repeater pulse output: TTL pulse switching between +5 V and ground
• Alarm Capability:
• Two-alarm setpoints: High or Low
• alarm limits, latching or non-latching
• Front panel pushbutton programmable
• Hysteresis, deadband, and low limit lockout are programmable; relays can be set as a fail-safe
• Alarms can be reset manually or automatically; remote reset via the auxiliary input
• Alarm Outputs: Two Form C relay contacts, rated 1 A at 115 V ac or 230 V ac
• Remote Programming:
• Remote programming is possible using an optional communications interface and PM Remote Software (If no communications are ordered, the unit can still be programmed with an optional USB programming cable.)
• Environmental:
• Indoor use only, installation category II per IEC 664 temperature: -10 °C to 50 °C operating per IEC 61010-1
• Humidity: maximum relative humidity 80% for temperatures up to 31 °C, decreasing linearly to 50% relative humidity at 40 °C
• Electrical Safety: Meets EN61010-1:2001, EC low voltage directive 72/23/EEC and 89/336/EEC

*Specifications are subject to change without notice.     

PM Remote Software is a free downloadable Windows-based software application that allows users to quickly and easily customize the configuration of Monarch’s ACT-1B, ACT-3X, F2A1X, and F2A3X panel tachometers. Set the mode of operation to RPM, RPS, or Frequency and select the input scale (pulses per revolution). Real-time data can be displayed directly on the PC along with min and max values. Decimal places and display update rate are user-configurable.

Click here for complete details and to download the software.

Features

• Allows quick setup of ACT-1B, ACT-3X, F2A1X, and F2A3X
• Display live data remotely on PC
  
• Unit configuration can be saved for reloading in the feature