voltage-dc-converters-data Downloads
32 downloads found
The UltraVolt® MPM series of proportional DC-to-DC converters provide compact, general purpose high voltage ...
The UltraVolt® LE Series of regulated DC-to-DC converters offer excellent low ripple and stability suitable for precision high voltage ...
SOC units can monitor the reading data of the battery pack and battery cells for the instantaneous State of Charge; Applicable for battery pack voltage up to 500VDC; Data values can be read out and programmed by Computer for remote operations; Accurate State of Charge reading with the measurement of shunt 500A / 50mV for SOCU-505A and SOCU-505B, SOCU-512A and SOCU-512B for 1200A / 50mV; 4setsof ...
The miniature, micro-sized M series is the ideal solution for applications requiring biasing voltage ranging from 0 to 3000 V and very small current—only 16.4 cc (1.00 in3). Less than 12.7 mm (0.5") high, these modules are ideal for low-profile ...
The Trek® 605A is a high voltage reference supply designed to provide precise control of output voltages in the range of 0 to +1 kVDC or 0 to -1 kVDC with an output current range of 0 to ±1 mADC. The Trek 605A provides two modes of operation: a fixed mode providing a constant +1 kV or -1 kV output, and a variable mode providing variable control of the output voltage with a one (1) volt ...
The vertical, micro-sized V series is the ideal solution for applications that require a bias voltage ranging from 0 to 3000 V and very small current, at only 13.8 cc (0.84 in3). With a footprint under 2.54 cm2 (1 in2), these modules are perfect for applications with limited board ...
Iris Power Stator Slot Couplers (SSCs) are by far the most sensitive partial discharge sensor in the world since they are installed directly underneath the wedges in high voltage stator slots. The data collected using Stator Slot Couplers are not affected by normal external interference (or noise) such as power system corona, output bus arcing or other ...
The Trek® 623B is a DC-stable, high voltage power amplifier designed to provide precise control of bi-polar output voltages. It features an all-solid-state design for high slew rate, low-noise operation and a wide bandwidth of DC to greater than 10 kHz . The four-quadrant, active output stage sinks or sources current into reactive or resistive loads throughout the output voltage range. This ...
The LANCIER Monitoring Rail-Module-Bus is a modular and robust sensor system. Several measuring modules are mounted on a DIN rail and are directly connected to one another by means of plug-in contacts. The supply voltage, data analysis and control panel as well as their transmission to the remote measuring stations are carried out via the RM-Basic ...
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA. The output stage offers either voltage, bipolar voltage or current re-transmission signals. For ease of use, a high efficiency switch mode power supply is fitted as standard and does not require any adjustment between ac or dc ...
The EC-2V is a two-channel voltage data logger that needs to be plugged in to the mains socket you want to measure. Setup the Logger using the Electrosoft software, then plug it ...
Measuring only 5.75 cc (0.35 in3), the highly compact, micro-sized UltraVolt® US series is specially designed to meet the needs of design engineers working with commercial, military, industrial, and medical applications. These modules allow access to voltages up to 500 V for customers with size-critical ...
The UltraVolt® Dual Polarity C integrates two high power DC-to-DC converters of opposite polarity into a single ...
The UltraVolt® XS series of extra-small high voltage power supplies is the smallest regulated DC-to-DC high voltage power supply for applications that require a bias voltage ranging from 0 to 100 V. Measuring only 1.3 cc (0.08 in3), these modules are ideal for use in size-critical ...
The EC-2VA is a single-phase voltage and current data logger that uses a flexible Rogowski coil and plug to connect to the mains supply/equipment you wish to measure. Setup the Logger using the Electrosoft software, then fit it to the distribution board or other point that you're going to ...
The EC-3V is a three-phase voltage data logger that can record 1, 2 or 3 phases. Simply connect to your supply. Setup the Logger using the Electrosoft software, then fit it to the distribution board or other point that you're going to ...