Energy Services In Kuwait
19 services found
by:The Sniffers based inBalen, BELGIUM
Thermographic surveys enable you to obtain the thermal pattern of an object’s surface. It is a non-destructive, no-touch, on-site method. Insight into the condition of installations Almost all processes and changes that take place within processes can be detected and analyzed. Our certified inspectors apply the best available techniques to give you clear insight into the condition of your ...
Manufactured by:Revolmixing based inCalgary, ALBERTA (CANADA)
Do you experience mixing problems such as: Solids settlement. No enough mixing. Over-mixing. Low turn-over. Unwanted byproducts. Low productivities. Let’s discuss your challenges and present our solutions!. ...
by:VIBSYS TECHNICAL SERVICES - Condition Monitoring Services, Kuwait based in, KUWAIT
Condition Monitoring Services - Dynamic Balancing, Laser Alignment, Vibration Analysis Contact: +965 69678166, shans@vibsys-ts.com, ...
by:VIBSYS TECHNICAL SERVICES - Condition Monitoring Services, Kuwait based in, KUWAIT
Condition Monitoring consultancy services Contact: +965 69678166, shans@vibsys-ts.com, ...
by:Accredited Test Laboratories based inDubai, UNITED ARAB EMIRATES
Basic diesel analysis is used to test the standard quality of diesel. It is generally required by companies or individuals running single or multiple transports/generators etc. This test identifies that the diesel is fit for your engine and has no harmful or hazardous effect. The test also reveals standard quality of the diesel and reveals whether it effects environment or not. Contact: ...
by:Environmental Technology Company (ETC) based inAl-Khobar, SAUDI ARABIA
ISC shall offer industry with practical and cost-effective solutions for a wide range of sludge treatment applications including crude oil tank bottoms, sludge from pits or waste lagoons and refinery generated oily ...
Manufactured by:Revolmixing based inCalgary, ALBERTA (CANADA)
CFD modeling is a tool to help determine the design parameters for mixing ...
by:The Sniffers based inBalen, BELGIUM
Steam losses are losses caused by defective steam traps, bypasses and process valves that start discharging steam with condensate causing high financial losses. Having invested in a steam system, it makes economic sense to maintain it at its optimum operational efficiency. Boilers and other steam plant producers are the most significant energy consumers in a refinery. Steam loss monitoring Our ...
by:Accredited Test Laboratories based inDubai, UNITED ARAB EMIRATES
Full Diesel Analysis reveals results to check complete aspects of diesel quality. It is generally required in two cases, first when someone buying it from sellers and the second if somebody experiencing problems with its use. The test covers most of the parameter and test methods to see whether diesel is as per prescribed standards or it has some otherwise results. Below is the full diesel ...
by:VIBSYS TECHNICAL SERVICES - Condition Monitoring Services, Kuwait based in, KUWAIT
Condition Monitoring consultancy services - Vibration Analysis, Dynamic balancing, Laser alignment, Lube oil analysis, Motor Current Signature Analysis (MCSA), Ultrasound analysis Contact: +965 69678166, shans@vibsys-ts.com, ...
by:Accredited Test Laboratories based inDubai, UNITED ARAB EMIRATES
DIN EN 590 is a standard defined by European Authorities to test the physical properties of diesel for sale purpose. It is necessary for all diesel fuels to meet the standards which are used in European countries. There are numerous companies following the same standards even in Middle East. Below is a list of parameters and their associated test methods used to check the fuel quality. Contact: ...
Manufactured by:Munters based inAmesbury, MASSACHUSETTS (USA)
Do you happen to have one of the many older and still steadily running Munters dehumidifiers operating in your facility? Like Munters and most other environmentally concerned companies, you might also be focusing on reducing the energy consumption and carbon foot print? If YES, Munters can provide retrofit solutions to optimize the energy efficiency in these older units, securing energy efficient ...
Manufactured by:Munters based inAmesbury, MASSACHUSETTS (USA)
Upgrade of MX process fan motor. The process fans on older Munters MX dehumidifiers are operating with AC induction motors. By upgrading these to modern and much more energy efficient EC (Electronic Commutator)fans, you will be granted energy savings at 50% or ...
Manufactured by:Munters based inAmesbury, MASSACHUSETTS (USA)
Munters helps you upgrade your equipment by enhancing them with the most recent technological advances and enhancements. No matter the application, upgrades to Munters equipment boost productivity, increase energy savings, reduce downtime and slash operating and maintenance ...
Manufactured by:Munters based inAmesbury, MASSACHUSETTS (USA)
All Munters equipment leaves our factories only after an extensive test procedure. A natural continuation is to have Munters’ qualified service team startup the equipment on site. We produce a performance values report documenting ambient conditions and all inlet and outlet parameters. We then compare that with how the machine should run on such a day using performance calculation ...
Manufactured by:Munters based inAmesbury, MASSACHUSETTS (USA)
Munters has a multinational experience with FanGrid upgrades of non-Munters AHU equipment. In facilities operating 24/7 we replace old belt drive fans with energy efficient direct drive EC fans, creating redundancy and substantial energy savings. These upgrades grant our customers a very short ROI, often at 2 years or ...
Manufactured by:Munters based inAmesbury, MASSACHUSETTS (USA)
Munters equipment is supported by an expert global service network for optimal performance. The extensive experience in process climate optimization, heat recovery and other upgrades provides optimal efficiency and performance improvements. Our aim is to help secure your climate, maintaining the efficiency of your equipment and ensuring uninterrupted, fault-free production. Munters service teams ...
Manufactured by:Rotork plc based inBath, UNITED KINGDOM
Rotork offers a tailor-made service programme designed to increase reliability and availability of valve actuator and control products via planned maintenance, predictive maintenance and asset ...
Manufactured by:Aereon, part of Cimarron group based inLegnano (MI), ITALY
AEREON can provide you with economical tip replacements for all OEM flare systems -- from simple utility-flare tip designs to more-complex steam flare tip systems typically used in downstream facilities. Custom-built in our own manufacturing facilities, each flare tip is designed to exacting standards by our highly experienced engineering team. Whether your flare tip is replacing a legacy Flare ...