Waste Gas Equipment For Energy Management In Australasia
-
PremiumManufactured by Inciner8 Limitedbased in UNITED KINGDOM
Incineration is a waste treatment process that involves the combustion of organic substances contained in waste materials. Incineration and other high-temperature waste treatment systems are described as “thermal treatment”. incineration of waste materials converts the waste into ash, flue gas and heat. The ash is mostly formed by the inorganic constituents of the waste and may take ...
-
PremiumManufactured by Inciner8 Limitedbased in UNITED KINGDOM
Inciner8 now offer a full range of containerised incineration systems, placing us at the forefront of the latest transportation and industrial trends. Containerisation enables immediate waste management as the units are fully assembled and pre-installed. ...
-
Manufactured by Eneraque Pty Ltdbased in AUSTRALIA
When waste is stored in landfill sites, micro-organisms break down the waste material causing gas to be released. This gas can be extracted from disposal site and made available for use as fuel. Eneraque manufactures, installs and maintains landfill gas flares purpose built for your waste ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Air assisted flares are comprised of two risers (waste gas and air) and a blower system that provides supplemental combustion air. Air is fed by the blower into the air riser, to combine with the process gas, which passes through its own secondary riser. Upon mixing, the high-pressure air flow causes turbulence in the waste gas stream, improving mixing, and ultimately combustion efficiency. These ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Steam assisted flares are flares designed to dispose of heavier hydrocarbon gases which have a tendency to smoke. In order to prevent smoke formation, steam is injected into the waste stream using peripheral steam rings, center stream spargers and/or inner induction tubes. Steam flares are used in applications where high pressure steam is available on site. Steam flares are typically found in ...
-
Manufactured by Clarke Energybased in UNITED KINGDOM
Absorption chillers can be used to deliver a trigeneration solution for a combined heat and power plant. Absorption chillers produce chilled water by heating two different substances that are in thermal equilibrium to separation, then reuniting them through heat removal. An example of two substances that may be used for this process is water and lithium bromide. Absorption chillers can be ...
-
Manufactured by Zeeco, Inc.based in USA
The world’s most in-demand flare for the world’s most punishing conditions. Zeeco’s UF series utility flare is ideal for onshore or offshore applications that do not require smokeless performance or where smokeless flaring can be managed without air or steam assist. Our UF flare series is one of the most in-demand flares of its kind for punishing conditions that include extreme ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
The Certified Ultra-Low Emissions Burner (CEB) is an ultra-low emissions vapor device that utilizes premix surface combustion to effectively combust waste gases in a compact footprint. With VOC destruction efficiencies of up to 99.99% and a NOx emissions guarantee of ≤ 15 ppmv at 3% oxygen, carbon monoxide emissions guarantee of, smokeless operation and no luminous flame, the CEB is the best ...
-
Manufactured by Cs Clean Systems AGbased in GERMANY
FABLINE is the standard CLEANSORB model for waste gas removal on factory-scale applications. Available in three column sizes, the system is readily adaptable to the requirements of both pilot line and full-scale manufacturing. Enabled by the built-in safety and efficiency of CS CLEAN SOLUTIONS proprietary CLEANSORB® media, and with several thousand installations worldwide, FABLINE is the ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
The Model 100 Continuum Ignitor utilizes a high voltage electric arc to ignite a combustible air/gas mixture. This arc typically occurs every 20 seconds for a two second duration (timing is adjustable). The Continuum provides a spark inside a ‘slipstream’ chamber that diverts a portion of the waste gas to create a combustible air/gas mixture. This allows the Continuum ignitor to ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Carbon dioxide is often used in fire extinguishers and snuffing systems with the intention of effectively extinguishing flames. When CO2 gas is a large percentage of a waste gas stream, at times it proves difficult to maintain a lit flare without the use of assist gas or a properly designed flame ring. Flare Industries’ industry-proven Flame Ring Flare Technology is recommended in low-BTU ...
-
Manufactured by Hydroflux Pty Ltdbased in AUSTRALIA
FlareWell® waste gas burners form part the anaerobic digestion process. FlareWell is designed to burn gas from the digestion process in excess of the gas necessary for the sludge heating system. The burner is automatic in operation and uses digester gas and/or LPG for pilot ...
-
Manufactured by Eneraque Pty Ltdbased in AUSTRALIA
Eneraque delivers state-of-the-art biogas generator and waste gas utilization. As leading providers and system integration experts, we’ll handle the entire process — so you get a complete gas-to-energy solution designed, manufactured, and installed to your site requirements. Eneraque has full comprehensive capabilities and extensive experience in all aspects of gas process design, ...
-
Manufactured by Clarke Energybased in UNITED KINGDOM
Approximately 25% of the usable energy of the fuel gas is released in the exhaust of the gas engine. This can be captured for cogeneration in a combined heat and power plant. This heat exits the engine at ~450oC as ‘high grade heat’, contrasting to ‘low-grade heat’ available from the generator cooling circuits. This high temperature and flow makes it well suited for ...
-
Manufactured by Windsor Engineeringbased in NEW ZEALAND
Utilising waste gas in process heating or power generation (gas engine) is a preferred method of disposal, but sometimes it is impractical due to distance from a suitable site. Flaring gas is the best alternative in this situation. A temporary flare may also be required for co-generation standby systems and during landfill ...
-
Manufactured by Eneraque Pty Ltdbased in AUSTRALIA
Industrial gases are rated process gases, wood gases and vapours from petrochemical processing and are notoriously difficult to purify. It is especially important to ensure that the purification process is uninterrupted. Eneraque has developed innovative solutions customised to the waste gas burners that are ideal for use as a backup system or as a reliable means for disposing industrial gases. ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
AEREON's Cyclone Series Air-assisted flares are comprised of two risers (waste gas and air) and a blower system that provides supplemental combustion air. Air is fed by the blower into the air riser, to eventually combine with the process gas, which passes through its own secondary riser and is distributed at the flare tip through a proprietary AEREON Starfire burner tip. Upon mixing at the flare ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
Triton sonic flare technology allows for safe, efficient and smokeless flaring at elevated oil and gas production rates by injecting sea water into the flame envelope. High pressure sea water injection reduces flare emissions, helps minimize overall radiation levels from the flame, abates combustion noise, and preserves flame characteristics during high wind events. The Triton sonic flare is ...
-
Manufactured by Clarke Energybased in UNITED KINGDOM
Exhaust gas heat exchangers (EGHE) utilise waste heat from the exhaust of the GE's Jenbacher gas engine cogeneration plant. They are typically located adjacent to the engine or are mounted on the roof of a containerised combined heat and power unit. They are present in a wide range of different applications and along with the other systems can be used to achieve overall system efficiencies of ...
-
Manufactured by AEREON, part of Cimarron groupbased in USA
The dynamic (velocity) seal is a simple innovation which ensures significant cost savings over time. The reverse conical baffle design reduces flow area in the flare tip while simultaneously increasing purge gas velocity. In combination with the dynamic seal, a constant flow of purge gas will maintain a seal in flare system, ensuring that air infiltration does not occur. A vortex effect is ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you